TIRE PRESSURE WARNING SYSTEM DATA LIST / ACTIVE TEST
-
Note:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tip:Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
READ DATA LIST
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
According to the display on the GTS, read the Data List.
Chassis > Tire Pressure Monitor > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Mode Status
Tire pressure warning system mode
NORMAL or TEST
NORMAL: Normal mode
TEST: Test mode
-
Main Tire
Number of main tire ID to be registered
4 or 5
4 or 5 displayed
4 displayed: w/o Full Size Spare Tire
5 displayed: w/ Full Size Spare Tire
2nd Tire
Number of 2nd tire ID to be registered
4 or 5
4 or 5 displayed
4 displayed: w/o Full Size Spare Tire
5 displayed: w/ Full Size Spare Tire
w/ ID Switching Function
Initialization Switch
Tire pressure warning reset switch
ON or OFF
ON: Switch on
OFF: Switch off
-
Vehicle Speed
Vehicle speed reading
min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on the combination meter assembly
Registered ID 1 Code
Registered ID1 code
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed
-
Registered ID 2 Code
Registered ID2 code
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed
-
Registered ID 3 Code
Registered ID3 code
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed
-
Registered ID 4 Code
Registered ID4 code
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed
-
Registered ID 5 Code
Registered ID5 code
min.: 0, max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed
w/ Full Size Spare Tire
ID 1 Temperature in Tire
ID1 temperature in tire
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature
If -40°C (-40°F) is displayed, data has not been received.
ID 2 Temperature in Tire
ID2 temperature in tire
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature
If -40°C (-40°F) is displayed, data has not been received.
ID 3 Temperature in Tire
ID3 temperature in tire
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature
If -40°C (-40°F) is displayed, data has not been received.
ID 4 Temperature in Tire
ID4 temperature in tire
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature
If -40°C (-40°F) is displayed, data has not been received.
ID 5 Temperature in Tire
ID5 temperature in tire
min.: -40°C (-40°F), max.: 215°C (419°F)
Actual tire temperature
If -40°C (-40°F) is displayed, data has not been received.
w/ Full Size Spare Tire
Initialization Switch Info
Tire pressure warning reset switch setting information
WITH or WITHOUT
WITH
-
ID 1 Tire Inflation Pressure
ID1 tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
If N/A is displayed, data has not been received.*2
ID 2 Tire Inflation Pressure
ID2 tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
If N/A is displayed, data has not been received.*2
ID 3 Tire Inflation Pressure
ID3 tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
If N/A is displayed, data has not been received.*2
ID 4 Tire Inflation Pressure
ID4 tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
If N/A is displayed, data has not been received.*2
ID 5 Tire Inflation Pressure
ID5 tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure
If N/A is displayed, data has not been received.*2
w/ Full Size Spare Tire
Threshold of Low-pressure (Lower Limit)
Tire inflation pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Specified tire pressure warning threshold lower limit displayed
If N/A is displayed, data has not been received.*2
ID 1 Initial Threshold of Low-pressure
ID1 initial threshold of low-pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization
-
ID 2 Initial Threshold of Low-pressure
ID2 initial threshold of low-pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization
-
ID 3 Initial Threshold of Low-pressure
ID3 initial threshold of low-pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization
-
ID 4 Initial Threshold of Low-pressure
ID4 initial threshold of low-pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization
-
ID 5 Initial Threshold of Low-pressure
ID5 initial threshold of low-pressure
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Tire pressure after initialization
w/ Full Size Spare Tire
Sensor ID Status
Status of ID selection
Main or 2nd
Status of ID selection
w/ ID Switching Function
Sensor ID Switch Function
Information on whether there is ID switching function or not
Without or With
Without: ID switching function is not equipped
With: ID switching function is equipped
w/ ID Switching Function
Number of Trouble Code
Number of DTCs recorded
min.: 0, max.: 255
Min.: 0, Max.: -
-
Tip:*1: Displayed only when the ID No. is not registered.
*2: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire).
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
Body Electrical > Combination Meter > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Indicat. Tire Pressure Warning System
Tire pressure warning light
OFF or ON
-