OUTER REAR VIEW MIRROR GLASS INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR LH (for LED Type Turn Signal Light)


    1. A001Y02C01
      *a

      Component without harness connected

      (Outer Mirror LH)

      Check the resistance.


      1. Measure the resistance according the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 8.5 to 11.5 Ω

        If the result is not as specified, replace the outer mirror LH.

    2. A001XC7C01
      *a

      Component without harness connected

      (Outer Mirror LH)

      Check the operation of the outer rear view mirror indicator.

      Note

      Do not apply a voltage of more than 6 V.


      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

        OK
        Tester Connection Specified Condition

        6 V battery positive (+) → Terminal 1

        6 V battery negative (-) → Terminal 2

        		 Outer rear view mirror indicator comes on

        If the result is not as specified, replace the outer mirror LH.

  2. INSPECT OUTER MIRROR RH (for LED Type Turn Signal Light)


    1. A001SDRC01
      *a

      Component without harness connected

      (Outer Mirror RH)

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 8.5 to 11.5 Ω

        If the result is not as specified, replace the outer mirror RH.

    2. A001XR9C01
      *a

      Component without harness connected

      (Outer Mirror RH)

      Check the operation of the outer rear view mirror indicator.

      Note

      Do not apply a voltage of more than 6 V.


      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

        OK
        Tester Connection Specified Condition

        6 V battery positive (+) → Terminal 1

        6 V battery negative (-) → Terminal 2

        		 Outer rear view mirror indicator comes on

        If the result is not as specified, replace the outer mirror RH.

  3. INSPECT OUTER MIRROR LH (for Bulb Type Turn Signal Light)


    1. A001WDGC02
      *a

      Component without harness connected

      (Outer Mirror LH)

      Check the resistance.


      1. Measure the resistance according the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 8.5 to 11.5 Ω

        If the result is not as specified, replace the outer mirror LH.

    2. A001VP9C03
      *a

      Component without harness connected

      (Outer Mirror LH)

      Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

      Note

      Do not apply a voltage of more than 6 V.


      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

        OK
        Tester Connection Specified Condition

        6 V battery positive (+) → Terminal 1

        6 V battery negative (-) → Terminal 2

        		 Outer rear view mirror indicator comes on

        If the result is not as specified, replace the outer mirror LH.

  4. INSPECT OUTER MIRROR RH (for Bulb Type Turn Signal Light)


    1. A001WLGC03
      *a

      Component without harness connected

      (Outer Mirror RH)

      Check the resistance.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 - 2 25°C (77°F) 8.5 to 11.5 Ω

        If the result is not as specified, replace the outer mirror RH.

    2. A001VRPC03
      *a

      Component without harness connected

      (Outer Mirror RH)

      Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

      Note

      Do not apply a voltage of more than 6 V.


      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

        OK
        Tester Connection Specified Condition

        6 V battery positive (+) → Terminal 1

        6 V battery negative (-) → Terminal 2

        		 Outer rear view mirror indicator comes on

        If the result is not as specified, replace the outer mirror RH.