LIGHTING SYSTEM Rear Fog Light Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light relay.

WIRING DIAGRAM

A005BBDE02

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Check that the relay operates.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in head position
      OK
      Rear fog light relay operates. (Rear fog light comes on.)

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. INSPECT REAR FOG LIGHT RELAY


    1. A005ABOE04

      Remove the rear fog light relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
      3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω

    NG

    REPLACE REAR FOG LIGHT RELAY

    OK

  3. CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - REAR FOG LIGHT RELAY)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L153-2 - Body ground Light control switch off → tail Below 1 V → 11 to 14 V
      L153-5 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - REAR COMBINATION LIGHT ASSEMBLY)


    1. Disconnect the R17 rear combination light assembly LH connector or the S18 rear combination light assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L153-3 - R17-1 Always Below 1 Ω
      L153-3 - S18-1 Always Below 1 Ω
      L153-3 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK)


    1. Disconnect the 2B instrument panel junction block assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L153-1 - 2B-26 Always Below 1 Ω
      2B-26 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. A005C8UE02
      Text in Illustration
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      Remove the instrument panel junction block assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2B-26 - MB-27 (RFGO) Always Below 1 Ω
      2B-26 - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here