CRUISE CONTROL SYSTEM(for 1ND-TV) DATA LIST / ACTIVE TEST

  1. READ DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Cruise Control / Data List.

    5. Read the Data List according to the display on the GTS.

      Powertrain > Cruise Control > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Cruise Control Main Switch

      Cruise control switch signal

      ON or OFF

      ON: Cruise control switch (ON-OFF button) pushed

      OFF: Cruise control switch (ON-OFF button) released

      -

      RES/ACC Switch

      +/RES switch signal

      ON or OFF

      ON: +/RES switch on

      OFF: +/RES switch off

      -

      SET/COAST Switch

      -/SET switch signal

      ON or OFF

      ON: -/SET switch on

      OFF: -/SET switch off

      -

      Cruise Control

      Cruise control system operation signal

      ON or OFF

      ON: Cruise control system operating

      OFF: Cruise control system not operating

      -

      CCS Mem Vehicle Spd

      Cruise control memorized speed

      min.: 0 km/h (0 mph), max.: 320 km/h (199 mph)

      Memorized speed: Cruise control activated

      -

      Cruise Control Mode

      Cruise control mode signal

      All Spd, Hi Spd or Normal

      All Spd: Vehicle-to-vehicle distance control mode (w/ full-speed following function)

      Hi Spd: Vehicle-to-vehicle distance control mode (w/o full-speed following function)

      Normal: Constant speed control mode

      -

      Stop Light SW 1 (M CPU)

      Stop light switch (Main-CPU) signal

      ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -

      Stop Light SW 1 (S CPU)

      Stop light switch (Sub-CPU) signal

      ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -

      Stop Light SW 2 (M CPU)

      Stop light switch (Main-CPU) signal

      ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -

      Vhcl Spd-Brake ECU

      Vehicle speed

      min.: -327 km/h (-203 mph), max.: 327 km/h (204 mph)

      Actual vehicle speed

      -

      Closed Throttle Position

      Accelerator pedal idle position signal

      ON or OFF

      ON: Accelerator pedal released

      OFF: Accelerator pedal depressed

      -

      ECM/PCM Command

      Origin of the drive force request

      Pedal, None or DS

      Pedal: Accelerator pedal depressed

      None: drive force not requested

      DS: Cruise control system operating

      -

      Request Driving Force

      Cruise control system request driving force

      Min.: -65536 N, Max.: 65534 N

      Actual request driving force

      -

      Cruise Control Status

      Status of the cruise control system

      OFF or ON

      OFF: Cruise control not used

      ON: Cruise control use

      -

      Cruise Cancel Request

      Status of the Cruise Cancel Request

      OFF or ON

      OFF: Cancel switch off

      ON: Cancel switch on

      -

      Driving Support ECU

      Status of the driving support ECU assembly

      With or Without

      With: ECU installed

      Without: ECU not installed

      -

      Clutch Switch

      Status of the clutch switch

      OFF or ON

      OFF: Clutch switch off

      ON: Clutch switch on

      -

      # Codes

      Number of DTCs

      min.: 0, max.: 255

      Actual number of DTCs

      -
      Tip:

      • If any DTCs are output, the value for a measurement item may be incorrect.

      • If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using the Data List.

  2. PERFORM ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform "Active Test" according to the display on the GTS.

      Tip:

      The ignition switch must be turned on to proceed with the Active Test using the GTS.

      Body Electrical > Combination Meter > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Indicat. Lamp Cruise

      Cruise control indicator (illuminated in green)

      ON / OFF

      -

      Indicat. SET

      Cruise control SET indicator

      ON / OFF

      -

      Cruise Indicator

      Cruise control indicator (illuminated in amber)

      ON / OFF

      w/ Multi-information Display (Segment LCD Type)