ECD SYSTEM(w/ Glow Plug Controller), Diagnostic DTC:P0335 and P0339

DTC Code DTC Name
P0335 Crankshaft Position Sensor "A" Circuit
P0339 Crankshaft Position Sensor "A" Circuit Intermittent

DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and a pickup coil.

The sensor plate has 58 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet. The sensor plate rotates and as each tooth passes through the pickup coil, a pulse signal is created.

The pickup coil generates 58 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail system is controlled.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0335

Crankshaft Position Sensor "A" Circuit

No crankshaft position sensor signal to ECM while cranking

(1 trip detection logic)

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • No. 1 crankshaft position sensor plate

  • ECM

Comes on

DTC stored

P0339

Crankshaft Position Sensor "A" Circuit Intermittent

Incorrect signal pattern is detected

(1 trip detection logic)

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • No. 1 crankshaft position sensor plate

  • ECM

Comes on

DTC stored
Table 1. DTC Detection Drive Pattern

DTC No.

DTC Detection Drive Pattern

P0335

The engine cranks 10 revolutions or more

P0339

The engine cranks 4 revolutions or more
Table 2. Related Data List

DTC No.

Data List

P0335

Engine Speed

P0339
Tip:

  • If DTC P0335 and/or P0339 is stored, the following symptoms may appear:

    • Difficult to start

    • Engine stalls due to fail-safe operation (fuel cut)

WIRING DIAGRAM

A353793E03

CAUTION / NOTICE / HINT

Note:

When replacing the ECM and/or engine assembly, perform ECM Initialization and Registration.

Click here

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Check the value on the GTS.

    1. Connect the GTS to the DLC3.

    2. Start the engine and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  • The engine speed can be confirmed in the Data List using the GTS. If there are no NE signals from the crankshaft position sensor despite the engine revolving, the engine speed will be indicated as zero. If the voltage output of the crankshaft position sensor is insufficient, the engine speed will be indicated as lower than the actual engine rpm.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. INSPECT CRANKSHAFT POSITION SENSOR

    1. Inspect the crankshaft position sensor.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE CRANKSHAFT POSITION SENSORClick here

    OK

  2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B119-1 - B212-121 (NE+)

      Always

      Below 1 Ω

      B119-2 - B212-122 (NE-)

      Always

      Below 1 Ω

      B119-1 or B212-121 (NE+) - Body ground and other terminals

      Always

      10 kΩ or higher

      B119-2 or B212-122 (NE-) - Body ground and other terminals

      Always

      10 kΩ or higher
      Tip:

      A DTC may also be stored when the ground of a shielded wire is faulty.

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

    OK

  3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

    B322410C01

    *a

    OK

    *b

    NG

    *c

    Clearance

    1. Check the crankshaft position sensor installation.

      OK

      Sensor is installed correctly.

    Result

    Result

    OK

    NG
    NG

    SECURELY REINSTALL SENSORClick here

    OK

  4. INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

    1. Inspect the teeth of the No. 1 crankshaft position sensor plate.

      OK

      No. 1 crankshaft position sensor plate does not have any cracks or deformation.

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATEClick here

    OK

  5. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  6. REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

    1. Replace the No. 1 crankshaft position sensor plate.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  7. SECURELY REINSTALL SENSOR

    1. Securely reinstall the crankshaft position sensor.

      Click hereClick here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  9. REPLACE CRANKSHAFT POSITION SENSOR

    1. Replace the crankshaft position sensor.

      Click hereClick here

    Result

    Proceed to

    NEXT
    NEXT

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Start the engine.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Confirm that the DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes

    Result

    Proceed to

    NEXT
    NEXT

    END