| DTC Code | DTC Name |
|---|---|
| P2080 | Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1 |
| P2084 | Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 |
| P242B | Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3 |
DESCRIPTION
Refer to DTC P0545 Click here.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Check the exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* *: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more. |
The change in the exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small. (2 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Check the No. 2 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* *: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more. |
The change in the No. 2 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small. (2 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Check the No. 3 exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving* *: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more. |
The change in the No. 3 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small. (2 trip detection logic) |
|
| DTC No. | Data List |
|---|---|
| P2080 P2084 P242B |
|
Tech Tips
Sensor 1 represents the sensor located upstream of the DOC catalytic converter.
Sensor 2 represents the sensor located upstream of the DPF catalytic converter.
Sensor 3 represents the sensor located downstream of the DPF catalytic converter.
If DTC P2080, P2084 or P242B is stored, the following symptoms may appear:
White smoke
WIRING DIAGRAM
Refer to DTC P0545 Click here.
INSPECTION PROCEDURE
Note
After replacing the ECM, the new ECM needs registration Click here and initialization Click here.
Tech Tips
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2080, P2084 OR P242B)
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P2080, P2084 or P242B is output | A |
| DTC P2080, P2084 or P242B and other DTCs are output | B |
| B |
|
GO TO DTC CHART Click here |
| A |
|
READ VALUE USING GTS (EXHAUST TEMPERATURE)
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
Record the exhaust temperature displayed on the GTS.
| NEXT |
|
INSPECT EXHAUST GAS TEMPERATURE SENSOR
Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
Stop the vehicle.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
Read the value.
| Result | ||||||||
|---|---|---|---|---|---|---|---|---|
|
| B |
|
REPLACE ECM Click here |
| A |
|
REPLACE EXHAUST GAS TEMPERATURE SENSOR
Tech Tips
Replace the exhaust temperature sensor that changed a small amount in "INSPECT EXHAUST GAS TEMPERATURE SENSOR".
Replace the exhaust gas temperature sensor Click here.
Replace the No. 2 exhaust gas temperature sensor Click here.
Replace the No. 3 exhaust gas temperature sensor Click here.
| NEXT |
|
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here |
REPLACE ECM
Replace the ECM Click here.
| NEXT |
|
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Leave the vehicle as is for 1 to 2 hours with the engine stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
Stop the vehicle.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.
Check the exhaust temperature after leaving the vehicle for 1 to 2 hours and after driving.
| Standard |
|---|
| +/-15°C(27°F) or more |
| NEXT |
|
END