OUTPUT SHAFT INSPECTION

PROCEDURE

  1. INSPECT NO. 1 OUTPUT SHAFT

    1. C112463

      Check the No. 1 output shaft for wear and damage.

    2. Using a dial indicator, check the No. 1 output shaft runout.

      Maximum Runout

      0.03 mm (0.00118 in.)

      If the runout exceeds the maximum, replace the No. 1 output shaft.

    3. C112464N02

      Using a micrometer, measure the outer diameter of the No. 1 output shaft journal surface.

      Standard

      Measured Part

      Outer Diameter mm (in.)

      A

      32.002 to 32.018 (1.2599 to 1.2605)

      B

      35.984 to 36.000 (1.4167 to 1.4173)

      C

      41.984 to 42.000 (1.6529 to 1.6535)

      D

      41.989 to 42.000 (1.6531 to 1.6535)

      E

      46.984 to 47.000 (1.8498 to 1.8504)

      F

      36.002 to 36.018 (1.4174 to 1.4180)

      If the outer diameter is below the minimum, replace the No. 1 output shaft.

  2. INSPECT 1ST AND 2ND SHIFT FORK SHAFT

    1. C113557

      Using a micrometer, measure the outer diameter of the 1st and 2nd shift fork shaft.

      Standard Outer Diameter

      13.982 to 14.00 mm (0.5505 to 0.5512 in.)

      Minimum Outer Diameter

      13.982 mm (0.5505 in.)

      If the outer diameter is less than the minimum, replace the 1st and 2nd shift fork shaft.

  3. INSPECT 3RD AND 4TH SHIFT FORK SHAFT

    1. C275840

      Using a micrometer, measure the outer diameter of the 3rd and 4th shift fork shaft.

      Standard Outer Diameter

      13.982 to 14.00 mm (0.5505 to 0.5512 in.)

      Minimum Outer Diameter

      13.982 mm (0.5505 in.)

      If the outer diameter is less than the minimum, replace the 3rd and 4th shift fork shaft.

  4. INSPECT 5TH AND 6TH SHIFT FORK SHAFT

    1. C113559

      Using a micrometer, measure the outer diameter of the 5th and 6th shift fork shaft.

      Standard Outer Diameter

      13.982 to 14.00 mm (0.5505 to 0.5512 in.)

      Minimum Outer Diameter

      13.982 mm (0.5505 in.)

      If the outer diameter is less than the minimum, replace the 5th and 6th shift fork shaft.

  5. INSPECT REVERSE SHIFT FORK SHAFT

    1. C275841

      Using a micrometer, measure the outer diameter of the reverse shift fork shaft.

      Standard Outer Diameter

      13.982 to 14.00 mm (0.5505 to 0.5512 in.)

      Minimum Outer Diameter

      13.982 mm (0.5505 in.)

      If the outer diameter is less than the minimum, replace the reverse shift fork shaft.

  6. INSPECT NO. 5 GEAR SHIFT FORK SHAFT

    1. C275842

      Using a micrometer, measure the outer diameter of the No. 5 gear shift fork shaft.

      Standard Outer Diameter

      15.966 to 15.984 mm (0.6286 to 0.6293 in.)

      Minimum Outer Diameter

      15.966 mm (0.6286 in.)

      If the outer diameter is less than the minimum, replace the No. 5 gear shift fork shaft.

  7. INSPECT NO. 1 GEAR SHIFT FORK

    1. C113562N02

      Using a vernier caliper, measure the No. 1 gear shift fork.

      Standard Inside Diameter and Thickness

      A

      9.50 to 9.80 mm (0.374 to 0.386 in.)

      B

      14.010 to 14.043 mm (0.552 to 0.553 in.)

      If the inside diameter or thickness is not as specified, replace the No. 1 gear shift fork.

  8. INSPECT NO. 2 GEAR SHIFT FORK

    1. C275886N02

      Using a vernier caliper, measure the No. 2 gear shift fork.

      Standard Inside Diameter and Thickness

      A

      9.50 to 9.80 mm (0.374 to 0.386 in.)

      B

      14.010 to 14.043 mm (0.552 to 0.553 in.)

      C

      14.70 to 15.30 mm (0.579 to 0.602 in.)

      If the inside diameter or thickness is not as specified, replace the No. 2 gear shift fork.

  9. INSPECT NO. 3 GEAR SHIFT FORK

    1. C113563N02

      Using a vernier caliper, measure the No. 3 gear shift fork.

      Standard Inside Diameter and Thickness

      A

      9.50 to 9.80 mm (0.374 to 0.386 in.)

      B

      14.010 to 14.043 mm (0.552 to 0.553 in.)

      If the inside diameter or thickness is not as specified, replace the No. 3 gear shift fork.

  10. INSPECT REVERSE SHIFT FORK

    1. C275843N02

      Using a vernier caliper, measure the reverse shift fork.

      Standard Inside Diameter and Thickness

      A

      4.40 to 4.56 mm (0.173 to 0.178 in.)

      B

      14.010 to 14.043 mm (0.552 to 0.553 in.)

      C

      14.7 to 15.3 mm (0.579 to 0.602 in.)

      If the inside diameter or thickness is not as specified, replace the reverse shift fork.

  11. INSPECT NO. 2 GEAR SHIFT HEAD

    1. C113561

      Using a vernier caliper, measure the No. 2 gear shift head.

      Standard Inside Diameter

      13.994 to 14.054 mm (0.551 to 0.553 in.)

      Maximum Inside Diameter

      14.054 mm (0.553 in.)

      If the inside diameter exceeds the maximum, replace the No. 2 gear shift head.

  12. INSPECT NO. 3 GEAR SHIFT HEAD

    1. C113560N02

      Using a vernier caliper, measure the No. 3 gear shift head.

      Standard Inside Diameter

      A

      15.994 to 16.054 mm (0.63 to 0.632 in.)

      B

      14.20 to 14.25 mm (0.559 to 0.561 in.)

      Maximum Inside Diameter

      A

      16.054 mm (0.632 in.)

      B

      14.25 mm (0.561 in.)

      If the inside diameter exceeds the maximum, replace the No. 3 gear shift head.

  13. INSPECT 1ST DRIVEN GEAR

    1. C113611

      Using a cylinder gauge, measure the inside diameter of the 1st driven gear.

      Standard Inside Diameter

      53.015 to 53.040 mm (2.0872 to 2.0882 in.)

      Maximum Inside Diameter

      53.040 mm (2.0882 in.)

      If the inside diameter exceeds the maximum, replace the 1st driven gear.

  14. INSPECT 2ND DRIVEN GEAR

    1. C113612

      Using a cylinder gauge, measure the inside diameter of the 2nd driven gear.

      Standard Inside Diameter

      56.015 to 56.030 mm (2.2053 to 2.2059 in.)

      Maximum Inside Diameter

      56.030 mm (2.2059 in.)

      If the inside diameter exceeds the maximum, replace the 2nd driven gear.

  15. INSPECT 3RD DRIVEN GEAR

    1. C113613

      Using a cylinder gauge, measure the inside diameter of the 3rd driven gear.

      Standard Inside Diameter

      42.015 to 42.040 mm (1.6541 to 1.6551 in.)

      Maximum Inside Diameter

      42.040 mm (1.6551 in.)

      If the inside diameter exceeds the maximum, replace the 3rd driven gear.

  16. INSPECT 4TH DRIVEN GEAR

    1. C113614

      Using a cylinder gauge, measure the inside diameter of the 4th driven gear.

      Standard Inside Diameter

      48.015 to 48.040 mm (1.8904 to 1.8913 in.)

      Maximum Inside Diameter

      48.040 mm (1.8913 in.)

      If the inside diameter exceeds the maximum, replace the 4th driven gear.

  17. INSPECT 1ST DRIVEN GEAR SYNCHRONIZER RING SET

    C157334C03

    *a

    Inner Ring

    1. Coat the 1st driven gear synchronizer ring set with gear oil.

    2. Install the inner ring to the 1st driven gear.

    3. C157335C02

      *a

      Middle Ring

      Install the middle ring to the 1st driven gear.

    4. C157336C02

      *a

      Outer Ring

      Install the outer ring to the 1st driven gear.

    5. C113625

      Coat the 1st driven gear with gear oil.

    6. Check that the 1st driven gear synchronizer ring set does not turn when the 1st driven gear synchronizer ring set is pushed to the 1st driven gear.

    7. C113618

      Using a feeler gauge, measure the clearance between the 1st driven gear synchronizer ring set back and the gear spline end.

      Standard Clearance

      0.98 to 1.82 mm (0.0386 to 0.0717 in.)

      Minimum Clearance

      0.98 mm (0.0386 in.)

      If the clearance is below the minimum, replace the 1st driven gear synchronizer ring set.

  18. INSPECT 2ND DRIVEN GEAR SYNCHRONIZER RING SET

    C157337C02

    *a

    Inner Ring

    1. Coat the 2nd driven gear synchronizer ring set with gear oil.

    2. Install the inner ring to the 2nd driven gear.

    3. C157338C02

      *a

      Middle Ring

      Install the middle ring to the 2nd driven gear.

    4. C157339C02

      *a

      Outer Ring

      Install the outer ring to the 2nd driven gear.

    5. C113626

      Coat the 2nd driven gear with gear oil.

    6. Check that the 2nd driven gear synchronizer ring set does not turn when the 2nd driven gear synchronizer ring set is pushed to the 2nd driven gear.

    7. C113619

      Using a feeler gauge, measure the clearance between the 2nd driven gear synchronizer ring set back and the gear spline end.

      Standard Clearance

      1.08 to 1.92 mm (0.0425 to 0.0756 in.)

      Minimum Clearance

      1.08 mm (0.0425 in.)

      If the clearance is below the minimum, replace the 2nd driven gear synchronizer ring set.

  19. INSPECT 3RD DRIVEN GEAR SYNCHRONIZER RING SET

    C157340C02

    *a

    Inner Ring

    1. Coat the 3rd driven gear synchronizer ring set with gear oil.

    2. Install the inner ring to the 3rd driven gear.

    3. C157341C02

      *a

      Middle Ring

      Install the middle ring to the 3rd driven gear.

    4. C157342C02

      *a

      Outer Ring

      Install the outer ring to the 3rd driven gear.

    5. C113627

      Coat the 3rd driven gear with gear oil.

    6. Check that the 3rd driven gear synchronizer ring set does not turn when the 3rd driven gear synchronizer ring set is pushed to the 3rd driven gear.

    7. C113620

      Using a feeler gauge, measure the clearance between the 3rd driven gear synchronizer ring set back and the gear spline end.

      Standard Clearance

      1.00 to 2.00 mm (0.0394 to 0.0787 in.)

      Minimum Clearance

      1.00 mm (0.0394 in.)

      If the clearance is below the minimum, replace the 3rd driven gear synchronizer ring set.

  20. INSPECT 4TH DRIVEN GEAR SYNCHRONIZER RING SET

    C157343C02

    *a

    Inner Ring

    1. Coat the 4th driven gear synchronizer ring set with gear oil.

    2. Install the inner ring to the 4th driven gear.

    3. C157344C03

      *a

      Middle Ring

      Install the middle ring to the 4th driven gear.

    4. C157345C02

      *a

      Outer Ring

      Install the outer ring to the 4th driven gear.

    5. C113628

      Coat the 4th driven gear with gear oil.

    6. Check that the 4th driven gear synchronizer ring set does not turn when the 4th driven gear synchronizer ring set is pushed to the 4th driven gear.

    7. C113621

      Using a feeler gauge, measure the clearance between the 4th driven gear synchronizer ring set back and the gear spline end.

      Standard Clearance

      0.92 to 1.88 mm (0.0362 to 0.074 in.)

      Minimum Clearance

      0.92 mm (0.0362 in.)

      If the clearance is below the minimum, replace the 4th driven gear synchronizer ring set.

  21. INSPECT NO. 1 TRANSMISSION HUB SLEEVE

    1. C116323N02

      Using a vernier caliper, measure the clearance between the No. 1 transmission hub sleeve and the No. 1 gear shift fork.

      Standard Clearance (A - B)

      0.10 to 0.50 mm (0.00394 to 0.0197 in.)

      If the clearance is outside the specifications, replace the No. 1 transmission hub sleeve and No. 1 gear shift fork.

  22. INSPECT NO. 2 TRANSMISSION HUB SLEEVE

    1. C116324N02

      Using a vernier caliper, measure the clearance between the No. 2 transmission hub sleeve and the No. 2 gear shift fork.

      Standard Clearance (A - B)

      0.10 to 0.50 mm (0.00394 to 0.0197 in.)

      If the clearance is outside the specifications, replace the No. 2 transmission hub sleeve and No. 2 gear shift fork.

  23. INSPECT NO. 2 OUTPUT SHAFT

    1. C112460

      Check the No. 2 output shaft for wear and damage.

    2. Using a dial indicator, check the No. 2 output shaft runout.

      Maximum Runout

      0.03 mm (0.00118 in.)

      If the runout exceeds the maximum, replace the No. 2 output shaft.

    3. C112461N02

      Using a micrometer, measure the outer diameter of the No. 2 output shaft journal surface.

      Standard

      Measured Part

      Outer Diameter mm (in.)

      A

      32.002 to 32.018 (1.2599 to 1.2605)

      B

      35.984 to 36.000 (1.4167 to 1.4173)

      C

      41.984 to 42.000 (1.6529 to 1.6535)

      D

      46.984 to 47.000 (1.8498 to 1.8504)

      E

      35.002 to 35.018 (1.3780 to 1.3787)

      If the outer diameter is below the minimum, replace the No. 2 output shaft.

  24. INSPECT 5TH DRIVEN GEAR

    1. C113615

      Using a cylinder gauge, measure the inside diameter of the 5th driven gear.

      Standard Inside Diameter

      48.015 to 48.040 mm (1.8904 to 1.8913 in.)

      Maximum Inside Diameter

      48.040 mm (1.8913 in.)

      If the inside diameter exceeds the maximum, replace the 5th driven gear.

  25. INSPECT 6TH DRIVEN GEAR

    1. C113616

      Using a cylinder gauge, measure the inside diameter of the 6th driven gear.

      Standard Inside Diameter

      42.015 to 42.040 mm (1.6541 to 1.6551 in.)

      Maximum Inside Diameter

      42.040 mm (1.6551 in.)

      If the inside diameter exceeds the maximum, replace the 6th driven gear.

  26. INSPECT REVERSE DRIVEN GEAR

    1. C113617

      Using a cylinder gauge, measure the inside diameter of the reverse driven gear.

      Standard Inside Diameter

      53.015 to 53.040 mm (2.0872 to 2.0882 in.)

      Maximum Inside Diameter

      53.040 mm (2.0882 in.)

      If the inside diameter exceeds the maximum, replace the reverse driven gear.

  27. INSPECT 5TH DRIVEN GEAR SYNCHRONIZER RING

    1. C113629

      Coat the 5th driven gear with gear oil.

    2. Check that the 5th driven gear synchronizer ring does not turn when the 5th driven gear synchronizer ring is pushed to the 5th driven gear.

    3. C113622

      Using a feeler gauge, measure the clearance between the 5th driven gear synchronizer ring back and the gear spline end.

      Standard Clearance

      0.80 to 1.60 mm (0.0315 to 0.063 in.)

      Minimum Clearance

      0.80 mm (0.0315 in.)

      If the clearance is below the minimum, replace the 5th driven gear synchronizer ring.

  28. INSPECT 6TH DRIVEN GEAR SYNCHRONIZER RING

    1. C113630

      Coat the 6th driven gear with gear oil.

    2. Check that the 6th driven gear synchronizer ring does not turn when the 6th driven gear synchronizer ring is pushed to the 6th driven gear.

    3. C113623

      Using a feeler gauge, measure the clearance between the 6th driven gear synchronizer ring back and the gear spline end.

      Standard Clearance

      0.80 to 1.60 mm (0.0315 to 0.063 in.)

      Minimum Clearance

      0.80 mm (0.0315 in.)

      If the clearance is below the minimum, replace the 6th driven gear synchronizer ring.

  29. INSPECT REVERSE DRIVEN GEAR SYNCHRONIZER RING

    1. C113631

      Coat the reverse driven gear with gear oil.

    2. Check that the reverse driven gear synchronizer ring does not turn when the reverse driven gear synchronizer ring is pushed to the reverse driven gear.

    3. C113624

      Using a feeler gauge, measure the clearance between the reverse driven gear synchronizer ring back and the gear spline end.

      Standard Clearance

      0.68 to 1.32 mm (0.0268 to 0.052 in.)

      Minimum Clearance

      0.68 mm (0.0268 in.)

      If the clearance is below the minimum, replace the reverse driven gear synchronizer ring.

  30. INSPECT NO. 3 TRANSMISSION HUB SLEEVE

    1. C116325N01

      Using a vernier caliper, measure the clearance between the No. 3 transmission hub sleeve and the No. 3 gear shift fork.

      Standard Clearance (A - B)

      0.10 to 0.50 mm (0.00394 to 0.0197 in.)

      If the clearance is outside the specifications, replace the No. 3 transmission hub sleeve and No. 3 gear shift fork.

  31. INSPECT NO. 4 TRANSMISSION HUB SLEEVE

    1. C116326N01

      Using a vernier caliper, measure the clearance between the No. 4 transmission hub sleeve and the reverse shift fork.

      Standard Clearance (A - B)

      0.15 to 0.41 mm (0.00591 to 0.0161 in.)

      If the clearance is outside the specifications, replace the No. 4 transmission hub sleeve and reverse shift fork.

  32. INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE

    1. C115414

      Using a dial indicator, measure the 1st driven gear thrust clearance.

      Standard Clearance

      0.10 to 0.35 mm (0.00394 to 0.0138 in.)

      Maximum Clearance

      0.35 mm (0.0138 in.)

      If the clearance exceeds the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft.

  33. INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE

    1. C115416

      Using a dial indicator, measure the 1st driven gear radial clearance.

      Standard Clearance

      0.015 to 0.068 mm (0.000591 to 0.00268 in.)

      Maximum Clearance

      0.068 mm (0.00268 in.)

      If the clearance exceeds the maximum, replace the 1st driven gear, needle roller bearing or No. 1 output shaft.

  34. INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE

    1. C115415

      Using a dial indicator, measure the 2nd driven gear thrust clearance.

      Standard Clearance

      0.11 to 0.46 mm (0.00433 to 0.0181 in.)

      Maximum Clearance

      0.46 mm (0.0181 in.)

      If the clearance exceeds the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft.

  35. INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE

    1. C113596

      Using a dial indicator, measure the 2nd driven gear radial clearance.

      Standard Clearance

      0.015 to 0.048 mm (0.000591 to 0.00189 in.)

      Maximum Clearance

      0.048 mm (0.00189 in.)

      If the clearance exceeds the maximum, replace the 2nd driven gear, needle roller bearing or No. 1 output shaft.

  36. INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE

    1. C113639

      Using a feeler gauge, measure the 3rd driven gear thrust clearance.

      Standard Clearance

      0.11 to 0.54 mm (0.00433 to 0.0213 in.)

      Maximum Clearance

      0.54 mm (0.0213 in.)

      If the clearance exceeds the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft.

  37. INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE

    1. C113643

      Using a dial indicator, measure the 3rd driven gear radial clearance.

      Standard Clearance

      0.015 to 0.066 mm (0.000591 to 0.0026 in.)

      Maximum Clearance

      0.066 mm (0.0026 in.)

      If the clearance exceeds the maximum, replace the 3rd driven gear, needle roller bearing or No. 1 output shaft.

  38. INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE

    1. C113640

      Using a feeler gauge, measure the 4th driven gear thrust clearance.

      Standard Clearance

      0.10 to 0.65 mm (0.00394 to 0.0256 in.)

      Maximum Clearance

      0.65 mm (0.0256 in.)

      If the clearance exceeds the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft.

  39. INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE

    1. C113644

      Using a dial indicator, measure the 4th driven gear radial clearance.

      Standard Clearance

      0.015 to 0.066 mm (0.000591 to 0.0026 in.)

      Maximum Clearance

      0.066 mm (0.0026 in.)

      If the clearance exceeds the maximum, replace the 4th driven gear, needle roller bearing or No. 1 output shaft.

  40. INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE

    1. C113604

      Using a feeler gauge, measure the 5th driven gear thrust clearance.

      Standard Clearance

      0.10 to 0.55 mm (0.00394 to 0.0217 in.)

      Maximum Clearance

      0.55 mm (0.0217 in.)

      If the clearance exceeds the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft.

  41. INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE

    1. C113605

      Using a dial indicator, measure the 5th driven gear radial clearance.

      Standard Clearance

      0.015 to 0.066 mm (0.000591 to 0.0026 in.)

      Maximum Clearance

      0.066 mm (0.0026 in.)

      If the clearance exceeds the maximum, replace the 5th driven gear, needle roller bearing or No. 2 output shaft.

  42. INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE

    1. C113602

      Using a feeler gauge, measure the 6th driven gear thrust clearance.

      Standard Clearance

      0.10 to 0.55 mm (0.00394 to 0.0217 in.)

      Maximum Clearance

      0.55 mm (0.0217 in.)

      If the clearance exceeds the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft.

  43. INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE

    1. C113603

      Using a dial indicator, measure the 6th driven gear radial clearance.

      Standard Clearance

      0.015 to 0.066 mm (0.000591 to 0.0026 in.)

      Maximum Clearance

      0.066 mm (0.0026 in.)

      If the clearance exceeds the maximum, replace the 6th driven gear, needle roller bearing or No. 2 output shaft.

  44. INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE

    1. C113606

      Using a feeler gauge, measure the reverse driven gear thrust clearance.

      Standard Clearance

      0.11 to 0.34 mm (0.00433 to 0.0134 in.)

      Maximum Clearance

      0.34 mm (0.0134 in.)

      If the clearance exceeds the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft.

  45. INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE

    1. C113607

      Using a dial indicator, measure the reverse driven gear radial clearance.

      Standard Clearance

      0.015 to 0.068 mm (0.000591 to 0.00268 in.)

      Maximum Clearance

      0.068 mm (0.00268 in.)

      If the clearance exceeds the maximum, replace the reverse driven gear, needle roller bearing or No. 2 output shaft.