IGNITION COIL AND SPARK PLUG INSTALLATION

PROCEDURE


  1. INSTALL SPARK PLUG (for Bank 1)


    1. B008BF7

      Install the 2 spark plugs onto the cylinder head sub-assembly.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Note

      If a component has been dropped or subjected a strong impact, replace it.

  2. INSTALL IGNITION COIL ASSEMBLY (for Bank 1)


    1. Install the 2 ignition coils onto the cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      If a component has been dropped or subjected a strong impact, replace it.

    2. Connect the 2 ignition coil connectors to the ignition coil.

      Note

      If a spring is used on the connector, make sure that the spring is back in the original position as shown in the illustration.

      B008BG2E01
      *a Spring

  3. INSTALL INJECTOR DRIVER

    Click here

  4. INSTALL SPARK PLUG (for Bank 2)


    1. B008BGM

      Install the 2 spark plugs onto the cylinder head sub-assembly.

      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

      Note

      If a component has been dropped or subjected a strong impact, replace it.

  5. INSTALL IGNITION COIL ASSEMBLY (for Bank 2)


    1. Install the 2 ignition coils onto the cylinder head cover sub-assembly with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      If a component has been dropped or subjected a strong impact, replace it.

    2. Connect the 2 ignition coil connectors to the ignition coil.

      Note

      If a spring is used on the connector, make sure that the spring is back in the original position as shown in the illustration.

      B008BENE01
      *a Spring

  6. INSTALL INJECTOR COVER (for Bank 2)


    1. Install the injector cover with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

    2. Engage the clamp, and install the fuel hoses.

  7. REMOVE SST


    1. Hoist the engine assembly up with an engine sling device and a mini crane.

    2. B008BEHE02

      Remove the SST.

      SST
      09250-53010
    3. B008BG4

      Install the 2 nuts.

    4. Remove the rope that is tying the front exhaust pipe sub-assembly to the front suspension cross member sub-assembly.

  8. REMOVE ENGINE HANGER

    Click here

  9. INSTALL EXHAUST MANIFOLD

    Click here

  10. INSTALL CLUTCH FLEXIBLE HOSE BRACKET (for RHD with Manual Transmission)


    1. Install the clutch flexible hose bracket with the bolt.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Connect the clutch flexible tube with the clip.

  11. CONNECT ENGINE WIRE


    1. Connect the engine wire with the wire harness clamp bracket mount bolt and 3 clamps.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

    2. Connect the engine wire with the 4 clamps.

  12. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  13. INSTALL FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY LH

    Click here

  14. INSTALL FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY RH

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here