TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B008HRA

      Install the transmission control cable assembly to the body with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. B008IVR

      Install the transmission control cable assembly to rear engine mounting insulator with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. B008JER

      Install the transmission control cable assembly to the transmission control cable support with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    4. Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    5. B008I9RC01
      *a P Position
      *b N Position

      Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

    6. B008IRI

      Install the transmission control cable assembly to the control shaft lever with the nut.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    7. Turn the nut of the transmission control cable assembly 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.

      Note

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B008HLUC26
      *a Nut
      *b Stopper
      *c Push in

      Turn the nut of the transmission control cable 180° clockwise. While holding the nut in place, push in the stopper to lock the nut.

      Note

      Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.

      Tech Tips

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    2. B008JDBC01
      *a Stopper
      *b Protrusion

      Connect the outer part of the transmission control cable assembly to the shift lever assembly.

      Note

      After installation, check that the outer part of the cable lock is protruding beyond portion A-A as shown in the illustration.

    3. B008I7G

      Connect the end of the transmission control cable assembly to the shift lever assembly.

      Note


      • Check that the shift lever position sensor and the shift lever are in neutral.

      • Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

      • Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.

  3. INSPECT SHIFT LEVER POSITION

    Click here

  4. ADJUST SHIFT LEVER POSITION

    Click here

  5. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  6. INSTALL BATTERY BRACKET REINFORCEMENT

    Click here

  7. INSTALL BATTERY CARRIER ASSEMBLY

    Click here

  8. CONNECT RADIATOR HOSE SUB-ASSEMBLY

    Click here

  9. INSTALL BATTERY TRAY

  10. INSTALL BATTERY

  11. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  12. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  13. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


    1. Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

  14. INSTALL AIR CLEANER CAP AND HOSE

    Click here

  15. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  16. CONNECT CABLE TO POSITIVE BATTERY TERMINAL

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here