REAR AXLE BEAM INSTALLATION

PROCEDURE

  1. INSTALL REAR AXLE CARRIER BUSHING LH

    1. When reusing the rear axle beam assembly:

      1. C270483C01

        *a

        Matchmark

        Align the arrow mark on a new rear axle carrier bushing LH with the matchmark on the rear axle beam assembly and temporarily install the rear axle carrier bushing LH to the rear axle beam assembly.

        Note:

        Be sure to install the rear axle carrier bushing in the same direction as it was before removal. The rear axle carrier bushing has to be installed in a specific direction.

    2. C270993C02

      *a

      Arrow Mark

      *b

      75°
      V100135

      Upper Side of the Vehicle
      V100136

      Front of the Vehicle

      When using a new rear axle beam assembly:

      1. Temporarily install a new rear axle carrier bushing LH as shown in the illustration.

        Note:

        Be sure to install the rear axle carrier bushing as shown in the illustration. The rear axle carrier bushing has to be installed in a specific direction.

    3. C266220C03

      *a

      Turn

      *b

      Hold

      Using SST, install the rear axle carrier bushing LH to the rear axle beam assembly.

      09710-30012

      09710-04101

      09950-40011

      09951-04020

      09952-04010

      09953-04030

      09954-04020

      09955-04051

      09957-04010

      09958-04011

      09950-60010

      09951-00620

      Note:

      • Do not damage the rubber portion when installing the rear axle carrier bushing.

      • Apply grease to the threads and tip of the SST center bolt before use.

  2. INSTALL REAR AXLE CARRIER BUSHING RH

    Tip:

    Perform the same procedure as for the LH side.

  3. TEMPORARILY INSTALL REAR AXLE BEAM ASSEMBLY

    1. Slowly jack up the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools, and temporarily install the rear axle beam assembly to the body with the 2 bolts (B).

      C272896C06

      *a

      Engine Lifter

      *b

      Wooden Block

      *c

      Attachment

      -

      -
      CAUTION:

      Make sure to secure the rear axle beam assembly to prevent it from dropping.

    2. Temporarily install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts (A) and 2 nuts.

      Note:

      Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.

      Tip:

      Insert the bolts with the threaded end facing the outside of the vehicle.

  4. INSTALL REAR LOWER COIL SPRING INSULATOR LH

    Click here

  5. INSTALL REAR LOWER COIL SPRING INSULATOR RH

    Tip:

    Perform the same procedure as for the LH side.

  6. INSTALL REAR UPPER COIL SPRING INSULATOR LH

    Click here

  7. INSTALL REAR UPPER COIL SPRING INSULATOR RH

    Tip:

    Perform the same procedure as for the LH side.

  8. INSTALL REAR COIL SPRING LH

    Click here

  9. INSTALL REAR COIL SPRING RH

    Tip:

    Perform the same procedure as for the LH side.

  10. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

    Click here

  11. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

    Click here

  12. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  13. INSTALL REAR NO. 4 BRAKE TUBE

    1. Install the rear No. 4 brake tube to the rear axle beam assembly with the nut.

      8.5 N*m

      87 kgf*cm

      75 in.*lbf

  14. INSTALL REAR NO. 3 BRAKE TUBE

    Tip:

    Perform the same procedure as for the rear No. 4 brake tube.

  15. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)

    1. Install the rear brake tube flexible hose with the bolt.

      19 N*m

      194 kgf*cm

      14 ft.*lbf

    2. Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 4 brake tube.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:

      • Do not kink or damage the brake tube.

      • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting parts.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click hereClick here

  16. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)

    1. Install the rear brake tube flexible hose with a new clip.

      Note:

      Install the clip as far as it will go.

    2. Using a union nut wrench, connect the rear brake tube flexible hose to the rear No. 3 brake tube.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:

      • Do not kink or damage the brake tube.

      • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting parts.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click hereClick here

  17. INSTALL REAR DISC

    1. Install the 2 rear discs.

      Click here

  18. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

    1. Install the rear disc brake caliper assembly LH with the rear flexible hose LH with the 2 bolts.

      72 N*m

      734 kgf*cm

      53 ft.*lbf

    2. Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.

      Note:

      Install the clip as far as it will go.

    3. Using a union nut wrench, connect the rear No. 4 brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:

      • Do not kink or damage the brake tube.

      • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting parts.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click hereClick here

  19. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  20. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

    1. Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the bolt.

      6.0 N*m

      61 kgf*cm

      53 in.*lbf

    2. Connect No. 3 parking brake cable assembly.

      Click here

  21. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tip:

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  22. INSTALL SKID CONTROL SENSOR WIRE LH

    Click here

  23. INSTALL SKID CONTROL SENSOR WIRE RH

    Tip:

    Perform the same procedure as for the LH side.

  24. INSTALL REAR FLOOR SIDE MEMBER BRACE SUB-ASSEMBLY

    1. for Type A:

      1. Install the rear floor side member brace sub-assembly with the 4 bolts and clip.

        54 N*m

        551 kgf*cm

        40 ft.*lbf

    2. for Type B:

      1. Install the rear floor side member brace sub-assembly with the 4 bolts.

        54 N*m

        551 kgf*cm

        40 ft.*lbf

  25. INSTALL REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

    1. Install the rear floor side member cover LH with the 2 bolts and nut.

  26. INSTALL REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)

    1. Install the rear floor side member cover RH with the 2 bolts and nut.

  27. ADJUST PARKING BRAKE

    Click here

  28. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

    for Hatchback, Wagon:Click hereClick here

    for Sedan:Click here

  29. FILL RESERVOIR WITH BRAKE FLUID

  30. BLEED BRAKE LINE

    Click hereClick here

  31. INSTALL REAR WHEELS

    103 N*m

    1050 kgf*cm

    76 ft.*lbf

  32. STABILIZE SUSPENSION

    Click here

  33. INSTALL REAR AXLE BEAM ASSEMBLY

    Click here

  34. INSTALL REAR WHEEL HOUSE LINER LH (w/ Wheel House Liner)

    Click here

  35. INSTALL REAR WHEEL HOUSE LINER RH (w/ Wheel House Liner)

    Tip:

    Perform the same procedure as for the LH side.

  36. INSPECT REAR WHEEL ALIGNMENT

    Click hereClick here

  37. CHECK FOR SPEED SENSOR SIGNAL

    w/o VSC (for Type A):Click here

    w/o VSC (for Type B):Click here

    w/ VSC:Click hereClick here