MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*1 |
SHIFT AND SELECT LEVER ASSEMBLY |
*2 |
SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING |
*3 |
DRAIN PLUG |
*4 |
GASKET |
*5 |
TRANSAXLE CASE OIL SEAL |
*6 |
SHIFT GATE PIN |
*7 |
NO. 1 LOCK BALL ASSEMBLY |
*8 |
NO. 2 LOCK BALL ASSEMBLY |
*9 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*10 |
TRANSMISSION CASE OIL SEAL |
*11 |
SELECTING BELL CRANK ASSEMBLY |
*12 |
SHIFT AND SELECT PIN |
*13 |
SPRING |
*14 |
O-RING |
*15 |
PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
MP grease |
★ |
Precoated part |
ILLUSTRATION
*A |
w/ Precoated Part |
*B |
w/o Precoated Part |
*1 |
CLUTCH RELEASE BEARING ASSEMBLY |
*2 |
CLUTCH RELEASE BEARING CLIP |
*3 |
CLUTCH RELEASE FORK SUB-ASSEMBLY |
*4 |
SHIFT DETENT BALL |
*5 |
RELEASE FORK SUPPORT |
*6 |
CLUTCH RELEASE FORK BOOT |
*7 |
SPRING |
*8 |
SPRING SEAT |
*9 |
DETENT BALL PLUG |
*10 |
REVERSE IDLER GEAR SHAFT BOLT |
*11 |
MANUAL TRANSMISSION CASE PLUG |
*12 |
GASKET |
*13 |
CONTROL CABLE BRACKET |
*14 |
MANUAL TRANSMISSION FILLER PLUG |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Release hub grease |
★ |
Precoated part |
ILLUSTRATION
*1 |
OUTPUT SHAFT COVER |
*2 |
FRONT TRANSAXLE CASE OIL SEAL |
*3 |
INPUT SHAFT FRONT BEARING |
*4 |
TRANSMISSION OIL SEPARATOR |
*5 |
INPUT SHAFT ASSEMBLY |
*6 |
NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE |
*7 |
NO. 2 OUTPUT SHAFT ASSEMBLY |
*8 |
NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE |
*9 |
OUTPUT SHAFT REAR BEARING SHIM |
*10 |
FRONT DIFFERENTIAL CASE FRONT BEARING OUTER RACE |
*11 |
FRONT DIFFERENTIAL CASE REAR BEARING OUTER RACE |
*12 |
FRONT DIFFERENTIAL CASE REAR SHIM |
*13 |
DIFFERENTIAL GEAR ASSEMBLY |
*14 |
TRANSMISSION MAGNET |
*15 |
OUTPUT SHAFT FRONT BEARING |
*16 |
NO. 1 OUTPUT SHAFT ASSEMBLY |
*17 |
OUTPUT SHAFT REAR BEARING SHAFT SNAP RING |
*18 |
INPUT SHAFT REAR BEARING SHAFT SNAP RING |
*19 |
NO. 1 OIL RECEIVER PIPE |
*20 |
MANUAL TRANSMISSION CASE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |
ILLUSTRATION
*1 |
1ST AND 2ND SHIFT FORK SHAFT |
*2 |
SHIFT FORK SHAFT BEARING |
*3 |
SHIFT ARM |
*4 |
PIN |
*5 |
E-RING |
*6 |
TRANSMISSION OIL SEPARATOR |
*7 |
NEEDLE ROLLER BEARING |
*8 |
5TH AND 6TH SHIFT FORK SHAFT |
*9 |
REVERSE SHIFT FORK |
*10 |
REVERSE SHIFT FORK SHAFT |
*11 |
NO. 1 GEAR SHIFT FORK |
*12 |
NO. 2 GEAR SHIFT HEAD |
*13 |
3RD AND 4TH SHIFT FORK SHAFT |
*14 |
NO. 2 GEAR SHIFT FORK |
*15 |
NO. 3 GEAR SHIFT HEAD |
*16 |
NO. 5 GEAR SHIFT FORK SHAFT |
*17 |
REVERSE IDLER GEAR |
*18 |
REVERSE IDLER THRUST WASHER |
*19 |
REVERSE IDLER GEAR SHAFT |
*20 |
NO. 3 GEAR SHIFT FORK |
*21 |
SLOTTED SPRING PIN |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
★ |
Precoated part |