FRONT SEAT SIDE AIRBAG ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

    • If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

      B006CU0

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the front seat airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY LH (When Installed to Vehicle)

    Note


    • When disposing of the front seat airbag assembly, use an unneeded vehicle to deploy the airbag.

    • Be sure to perform the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B006EZHN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Remove the 4 bolts and tilt the front seat assembly LH backward.

      Click here

    4. Install SST.


      1. B006F27N01

        Connect SST to the front seat airbag assembly LH.

        SST
        09082-00820

        CAUTION:

        B006FN6

        • Do not deploy if the front seat airbag assembly LH is loose.

        • If deployed while the front seat airbag assembly LH is loose, the front seat airbag assembly LH may fly off and cause serious injuries.

      2. Connect SST together (09082-00700 and 09082-00820).

        SST
        09082-00700

        Note

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.

    5. Return the front seat assembly LH to its original position.

      Click here

      CAUTION:

      Check that there is no looseness in the front seat assembly LH.

      B006FK9

    6. Deploy the airbag.


      1. B0069JFC48
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

      2. While maintaining sufficient clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

        CAUTION:


        • Do not deploy with all the doors and door windows open.

        • If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.

        B006C3G

        Note

        Take care not to damage SST wire harness.

      3. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      5. Press SST activation switch to deploy the airbag.

        CAUTION:


        • Do not deploy with people inside or around the vehicle.

        • If deployed with people inside or around the vehicle, serious injuries may occur.

        B0069TC

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    7. Remove the front seat airbag assembly LH.

      Click here

      CAUTION:


      • B0069JA

        The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B006ETE

        Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

      • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B006EJC

        Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

      • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • After removal, quickly seal the front seat airbag assembly LH in a plastic bag.

    8. Dispose of the front seat airbag assembly LH.


      1. Place the front seat airbag assembly LH in a plastic bag, tie it tightly and dispose of it according to local regulations.

        CAUTION:


        • B006BM0

          The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • If not left alone for 30 minutes or more, burns may occur when touched.

        • B006BSL

          Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

        • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

        • B006C5H

          Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

        • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

        • B006BR6

          Never dispose of a front seat airbag assembly LH with an undeployed airbag.

        • If an undeployed front seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

        • Always wash your hands with water after completing the operation.

  3. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY LH (When not Installed to Vehicle)

    Note

    Be sure to perform the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. B006EZHN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the front seat airbag assembly LH.

      Click here

    3. B006GDLC91
      *a Wire Diameter
      B006GBM Stripped Wire

      Using braided wire, tie down the front seat airbag assembly LH to an unneeded tire.

      Wire
      Cross-sectional area of stripped wire
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire harness is too thin or an alternative object is used to tie down the front seat airbag assembly LH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the cross-sectional area of stripped wire:

      Area = 3.14 x (Diameter)2/ 4


      1. B006ESG

        Install the 2 nuts to the front seat airbag assembly LH.

      2. B006EGD

        Wind 2 or more wires around the stud bolts of the front seat airbag assembly LH as shown in the illustration.

      3. B006BE0C01
        *a Width
        *b Inner Diameter
        *c Deployment Side

        Position the front seat airbag assembly LH inside the tire with the airbag deployment side facing inward.

        Minimum tire size
        Must exceed the following dimensions
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        Note

        The tire may be damaged by the airbag deployment, so use an unneeded tires.

    4. Install SST.


      1. B0069P8N01

        Connect SST to the front seat airbag assembly LH.

        SST
        09082-00820

    5. Place the tires.


      1. B006B9GC01
        *a Tires (2 or more)

        Place at least 2 tires under the tire to which the front seat airbag assembly LH is tied.

      2. Place at least 2 tires onto the tire to which the front seat airbag assembly LH is tied. The top tire should have a wheel installed.

        Note


        • Do not place SST connector under the tire because it could be damaged.

        • The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

      3. B006AKO

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.

    6. Install SST.


      1. B006FD8C01
        *a 10 m (32.8 ft.) or more

        Connect SST together (09082-00700 and 09082-00820).

        SST
        09082-00700

        Note

        To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tires.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat airbag assembly LH is tied.

      3. Press SST activation switch to deploy the airbag.

        CAUTION:


        • Do not deploy with people around the tire.

        • If deployed with people around the tire, serious injuries may occur.

        B006BWO

        Tech Tips

        The airbag is deployed as the LED of SST activation switch comes on.

    8. Dispose of the front seat airbag assembly LH.

      CAUTION:


      • B006BM0

        The front seat airbag assembly LH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • If not left alone for 30 minutes or more, burns may occur when touched.

      • B006BSL

        Do not apply water etc. to a front seat airbag assembly LH with a deployed airbag.

      • If water is applied to the front seat airbag assembly LH immediately after deployment, burns may occur from the resulting steam.

      • B006C5H

        Always wear safety glasses and gloves when handling a deployed front seat airbag assembly LH.

      • If the front seat airbag assembly LH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

      • B006BR6

        Never dispose of a front seat airbag assembly LH with an undeployed airbag.

      • If an undeployed front seat airbag assembly LH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

      • Always wash your hands with water after completing the operation.


      1. Remove the front seat airbag assembly LH from the tire.

      2. Place the front seat airbag assembly LH in a plastic bag, tie it tightly, and dispose of it according to local regulations.