FRONT DOOR LOCK(for Sedan) INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR LOCK ASSEMBLY LH

   1. 

      *a	Unlock
      *b	Lock
      *c	Component without harness connected (Front Door Lock Assembly LH)

      Check the operation of the door lock motor.

      1. Apply battery voltage and check the operation of the door lock motor.

         OK

         Connection	Result
         Battery positive (+) → Terminal 4 (L) Battery negative (-) → Terminal 1 (UL)	Locks
         Battery positive (+) → Terminal 1 (UL) Battery negative (-) → Terminal 4 (L)	Unlocks

         If the result is not as specified, replace the front door lock assembly LH.

   2. Check the operation of the door unlock detection switch. (for LHD or with Entry and Start System)

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         7 (E) - 8 (LSSR)	Locked	10 kΩ or higher
         7 (E) - 8 (LSSR)	Unlocked	Below 1 Ω

         If the result is not as specified, replace the front door lock assembly LH.

   3. 

      *a	Unlock
      *b	Neutral
      *c	Lock
      *d	Component without harness connected (Front Door Lock Assembly LH)

      Check the operation of the door key lock and unlock switch. (for LHD)

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         9 (L) - 7 (E)	Held to lock side	Below 1 Ω
         9 (L) - 7 (E)	Neutral or held to unlock side	10 kΩ or higher
         10 (UL) - 7 (E)	Held to unlock side	Below 1 Ω
         10 (UL) - 7 (E)	Neutral or held to lock side	10 kΩ or higher

         If the result is not as specified, replace the front door lock assembly LH.

2. INSPECT FRONT DOOR LOCK ASSEMBLY RH

   1. 

      *a	Unlock
      *b	Lock
      *c	Component without harness connected (Front Door Lock Assembly RH)

      Check the operation of the door lock motor.

      1. Apply battery voltage and check the operation of the door lock motor.

         OK

         Connection	Result
         Battery positive (+) → Terminal 4 (L) Battery negative (-) → Terminal 1 (UL)	Locks
         Battery positive (+) → Terminal 1 (UL) Battery negative (-) → Terminal 4 (L)	Unlocks

         If the result is not as specified, replace the front door lock assembly RH.

   2. Check the operation of the door unlock detection switch. (for RHD or with Entry and Start System)

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         7 (LSSR) - 8 (E)	Locked	10 kΩ or higher
         7 (LSSR) - 8 (E)	Unlocked	Below 1 Ω

         If the result is not as specified, replace the front door lock assembly RH.

   3. 

      *a	Unlock
      *b	Neutral
      *c	Lock
      *d	Component without harness connected (Front Door Lock Assembly RH)

      Check the operation of the door key lock and unlock switch. (for RHD)

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         6 (L) - 8 (E)	Held to lock side	Below 1 Ω
         6 (L) - 8 (E)	Neutral or held to unlock side	10 kΩ or higher
         5 (UL) - 8 (E)	Held to unlock side	Below 1 Ω
         5 (UL) - 8 (E)	Neutral or held to lock side	10 kΩ or higher

         If the result is not as specified, replace the front door lock assembly RH.