ECD SYSTEM, Diagnostic DTC:P0016

DTC Code DTC Name
P0016 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

DESCRIPTION

The ECM uses 2 sensors to detect the engine speed and the position of the crankshaft and camshaft. The crankshaft position sensor detects the engine speed and top dead center position of the crankshaft. The camshaft position sensor determines when the cylinder is at the top dead center of the compression or exhaust stroke.

The exhaust gas value worsens due to an angular error between the crankshaft and camshaft. The ECM stores DTC P0016 if the angular error between the crankshaft and camshaft exceeds the threshold.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0016

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

Phase deviation in crankshaft and camshaft position sensor signals.

(3 trip detection logic)

  • Camshaft and camshaft timing sprocket installation condition

  • Camshaft position sensor installation condition

  • Valve timing

  • Looseness in timing chain

  • ECM

Does not come on

DTC stored

WIRING DIAGRAM

Refer to DTC P0335.

Click here

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, the ECM needs registration and initialization.

Click here

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. INSPECT CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITION

    1. A318369

      Remove the cylinder head cover sub-assembly so that the camshaft timing sprocket is visible.

      Click here

    2. Check the camshaft and camshaft timing sprocket installation condition.

      OK

      Camshaft and camshaft timing sprocket securely installed without looseness.

      Tip:

      The holes for the bolts which connect the camshaft timing sprocket to the camshaft are long. If there is looseness, the parts can slide and become misaligned.

    Result

    Proceed to

    OK

    NG
    NG

    CHECK CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITIONClick here

    OK

  2. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

    1. Check the camshaft position sensor installation.

      OK

      Sensor is installed correctly.

    Result

    Proceed to

    OK

    NG
    NG

    SECURELY REINSTALL SENSORClick here

    OK

  3. CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

    1. Remove the cylinder head cover sub-assembly so that the camshaft timing sprocket is visible.

      Click here

    2. Rotate the crankshaft, and then using SST, secure the crankshaft at compression top dead center.

      Click here

    3. Check the camshaft alignment marks.

      Click here

      OK

      The valve timing is correctly aligned.

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE ENGINE MECHANICAL SYSTEMClick here

    OK

  4. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  5. REPAIR OR REPLACE ENGINE MECHANICAL SYSTEM

    1. Repair or replace for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT
    NEXT

    END

  7. SECURELY REINSTALL SENSOR

    1. Securely reinstall sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. CHECK CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITION

    1. Check the camshaft and camshaft timing sprocket installation condition and perform reinstallation if necessary.

      Tip:

      The camshaft and camshaft timing sprocket installation condition can be checked using SST.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here