REAR NO. 2 SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

  1. INSTALL REAR NO. 2 SEAT PROTECTOR

    1. Clean the rear No. 2 seat leg sub-assembly surface.

    2. B298185

      Attach a new rear No. 2 seat protector in the position shown in the illustration.

  2. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY

    Click here

  3. INSTALL SEAT SPRING SILENCER LH

    1. Clean the No. 2 seatback frame sub-assembly LH surface.

    2. B275749

      Attach a new seat spring silencer LH in the position shown in the illustration.

  4. INSTALL SEAT SPRING SILENCER RH

    Tip:

    Use the same procedure described for the LH side.

  5. INSTALL REAR SEAT RECLINING CONTROL CABLE LH

    1. B275748E03

      Install the rear seat reclining control cable LH in the order shown in the illustration.

    2. Attach the 2 clamps of the cable ends.

    3. Install a new cable tie.

      Table 1. Text in Illustration

      *1

      Cable Tie

      *2

      Clamp
    4. B272385E03

      Cut off the end of the cable tie as shown in the illustration.

      Table 2. Text in Illustration

      *a

      Cut Here

      *b

      5 mm (0.20 in.)

      *c

      Correct

      *d

      Incorrect
      Tip:

      Make sure that the end of the cable tie faces the seatback board.

  6. INSTALL REAR SEAT RECLINING CONTROL CABLE RH

    Tip:

    Use the same procedure described for the LH side.

  7. INSTALL 3RD SEAT STRAP LH

    1. Install the 3rd seat strap LH with the screw.

      B275746E03
      Table 3. Text in Illustration

      *1

      Seatback Frame Wire

      -

      -

  8. INSTALL 3RD SEAT STRAP RH

    Tip:

    Use the same procedure described for the LH side.

  9. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH

    1. B275740E01

      Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the rear No. 2 seat cushion pad LH with new hog rings.

      Table 4. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  10. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  11. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH

    1. B275744E02

      Pass the No. 2 seat cushion frame sub-assembly LH through the slits in the rear seat cushion under cloth LH and install the rear seat cushion under cloth LH.

      Table 5. Text in Illustration

      *1

      Slit
    2. B275742E01

      Pass the No. 2 seat cushion frame sub-assembly LH through the slits in the No. 2 seat cushion cover sub-assembly LH and install the No. 2 seat cushion frame sub-assembly LH.

      Table 6. Text in Illustration

      *1

      Slit

    3. Attach the hooks.

    4. B275737E01

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Table 7. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    5. B275735E01

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Table 8. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. B275733E01

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Table 9. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    7. B275731E01

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Table 10. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  12. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  13. INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH

    1. B222883

      Attach the 2 claws to install the rear seat lower cushion hinge cover RH.

  14. INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

    1. B222882

      Attach the 2 claws to install the rear seat lower cushion hinge cover LH.

  15. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH

    1. Using a T45 "TORX" socket wrench, install the rear No. 2 seat cushion assembly LH and 2 spacers with the 2 "TORX" bolts to the No. 2 seatback frame assembly LH.

      14 N*m

      143 kgf*cm

      10 ft.*lbf

    2. B275728

      When reusing the nut:

      1. Clean the threads of the nut with non-residue solvent.

      2. Apply adhesive to the threads of the nut.

        Adhesive

        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      3. Temporarily install the nut and 2 bolts.

    3. When using a new nut:

      1. Temporarily install a new nut and the 2 bolts.

    4. Tighten the nut and 2 bolts.

      for Nut

      20 N*m

      204 kgf*cm

      15 ft.*lbf

      for Bolt

      42 N*m

      428 kgf*cm

      31 ft.*lbf

    5. Install the No. 2 seat No. 2 suspension link and spacer.

    6. Install the spacer with the bolts.

      42 N*m

      428 kgf*cm

      31 ft.*lbf

    7. Install a new E-ring.

    8. Install the No. 2 seat No. 1 suspension link and spacer.

    9. Install the spacer with the bolts.

      42 N*m

      428 kgf*cm

      31 ft.*lbf

    10. Install a new E-ring.

  16. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  17. INSTALL REAR SEAT CUSHION SPACER LH

    1. B222879

      Install the rear seat cushion spacer LH.

  18. INSTALL REAR SEAT CUSHION SPACER RH

    Tip:

    Use the same procedure described for the LH side.

  19. INSTALL REAR NO. 2 SEAT CUSHION SPRING LH

    1. B222878

      Attach the hook to install the rear No. 2 seat cushion spring LH.

  20. INSTALL REAR NO. 2 SEAT CUSHION SPRING RH

    Tip:

    Use the same procedure described for the LH side.

  21. INSTALL REAR SEAT INNER RECLINING COVER LH

    1. B222877

      Attach the hook to install the rear seat inner reclining cover LH.

  22. INSTALL REAR SEAT INNER RECLINING COVER RH

    Tip:

    Use the same procedure described for the LH side.

  23. INSTALL REAR SEAT SIDE HINGE MALE COVER LH

    1. B222876

      Attach the hook to install the rear seat side hinge male cover LH.

    2. Install the screw.

  24. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

    Tip:

    Use the same procedure described for the LH side.

  25. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

    1. B222875E01

      Using hog ring pliers, install the center of the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad LH with new hog rings.

      Table 11. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B222874E01

      Using hog ring pliers, install the upper part of the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad LH with new hog rings.

      Table 12. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  26. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  27. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD LH

    1. B222873

      Install the rear No. 2 seatback cover with pad LH.

    2. Pass the 3rd seat strap through the hole of the rear No. 2 seatback cover with pad LH to the surface.

  28. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD RH

    Tip:

    Use the same procedure described for the LH side.

  29. INSTALL REAR SEATBACK LOCK HOOK LH

    1. B222872

      Install the rear seatback lock hook LH.

  30. INSTALL REAR SEATBACK LOCK HOOK RH

    Tip:

    Use the same procedure described for the LH side.

  31. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY LH

    1. B222871

      Attach the 4 claws to install the 2 rear No. 2 seat headrest supports assemblies.

  32. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  33. INSTALL SEATBACK FELT LH

    B275722E01

    1. Clean the rear seatback board sub-assembly LH surface.

    2. Attach a new seatback felt LH in the position shown in the illustration.

      Table 13. Text in Illustration

      *1

      Seatback Felt

  34. INSTALL SEATBACK FELT RH

    Tip:

    Use the same procedure described for the LH side.

  35. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

    1. B230512

      Attach the 6 hooks to install the rear seatback cloth LH to the rear seatback board sub-assembly LH.

    2. B298174E01

      Attach the 2 hooks.

    3. Pass the 3rd seat strap through the hole of the rear seatback board sub-assembly LH to the surface.

      Table 14. Text in Illustration

      *1

      3rd Seat Strap

      *2

      Seatback Felt

    4. Attach the 3 claws.

    5. Install the 2 screws.

    6. Remove the peeling paper from the seatback felt LH while being careful not to touch the exposed adhesive.

    7. Attach the hooks to install the rear seatback board sub-assembly LH.

  36. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  37. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    1. B275717

      Attach the 2 hooks to install the rear No. 2 seat reclining cover LH.

    2. Install the screw.

  38. INSTALL REAR NO. 2 SEAT RECLINING COVER RH

    Tip:

    Use the same procedure described for the LH side.

  39. INSTALL REAR SEAT CUSHION HINGE COVER

    1. B273979

      Attach the 2 guides to install the rear seat cushion hinge cover.

    2. Install the screw.

    3. Install the screw.

  40. INSTALL NO. 2 SEAT HEADREST ASSEMBLY LH

    1. Install the No. 2 seat headrest assembly LH.

  41. INSTALL NO. 2 SEAT HEADREST ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.