POWER DOOR LOCK CONTROL SYSTEM(for Sedan) DATA LIST / ACTIVE TEST
DATA LIST
Tip:Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
Body Electrical > Main Body > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch
ON or OFF
ON: Ignition key inserted
OFF: Ignition key not inserted
*1
ACC SW
Ignition switch ACC signal
ON or OFF
ON: Ignition switch ACC
OFF: Ignition switch off
-
IG SW
Ignition switch IG signal
ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
RR Door Courtesy SW
Rear door courtesy light switch RH signal
ON or OFF
ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW
Rear door courtesy light switch LH signal
ON or OFF
ON: Rear door LH open
OFF: Rear door LH closed
-
Door Lock SW-Lock
Door control switch (power window regulator master switch assembly) lock signal
ON or OFF
ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock
Door control switch (power window regulator master switch assembly) unlock signal
ON or OFF
ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Key SW-Lock
Driver door key-linked lock / unlock switch lock signal
ON or OFF
ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position
-
Door Key SW-Unlock
Driver door key-linked lock / unlock switch unlock signal
ON or OFF
ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position
-
FR Door Lock Pos
Front door RH unlock detection switch signal
LOCK or UNLOCK
LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
*4
FR Door Courtesy SW
Front door courtesy light switch RH signal
ON or OFF
ON: Front door RH open
OFF: Front door RH closed
-
FL Door Lock Pos
Front door LH unlock detection switch signal
LOCK or UNLOCK
LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
*5
FL Door Courtesy SW
Front door courtesy light switch LH signal
ON or OFF
ON: Front door LH open
OFF: Front door LH closed
-
RR-Door Lock Pos SW
Rear door RH and LH unlock detection switch signal
ON or OFF
ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*2, *6
RL-Door Lock Pos SW
Rear door RH and LH unlock detection switch signal
ON or OFF
ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
*3, *6
Luggage Courtesy SW
Luggage compartment door courtesy switch signal
ON or OFF
ON: Luggage compartment door open
OFF: Luggage compartment door closed
-
*1: w/o Entry and Start System
*2: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.
*3: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.
*4: for RHD or with Entry and Start System
*5: for LHD or with Entry and Start System
*6: w/ Entry and Start System
ACTIVE TEST
Tip:Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > Main Body > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Door Lock
Door lock motor
OFF/Unlock/Lock
-
Trunk and Back-Door Open
luggage compartment door lock motor
OFF/ON
-