TRANSFER ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | FRONT PROPELLER SHAFT ASSEMBLY | *2 | CONSTANT VELOCITY UNIVERSAL JOINT WASHER |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |  |
Do not apply lubricants |
ILLUSTRATION
| *1 | REAR ENGINE MOUNTING INSULATOR | *2 | REAR ENGINE MOUNTING MEMBER |
| *3 | TRANSFER ASSEMBLY | *4 | NO. 2 PARKING RELEASE CABLE BRACKET SUB-ASSEMBLY |
| *5 | AUTOMATIC TRANSMISSION ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ★ | Precoated part |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | NO. 2 TRANSFER CASE PLUG | *2 | OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY |
| *3 | TRANSFER CASE BREATHER PLUG | *4 | TRANSFER CASE PLUG |
| *5 | TRANSFER DRAIN PLUG | *6 | TRANSFER FILLER PLUG |
| *7 | TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL | *8 | TRANSFER FILLER PLUG GASKET |
| *9 | TRANSFER OUTPUT SHAFT COMPANION FLANGE BOLT | *10 | O-RING |
| *11 | TRANSFER DRAIN PLUG GASKET | *12 | TRANSFER CASE GASKET |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
MP grease |
ILLUSTRATION
| *1 | DIFFERENTIAL CASE NEEDLE ROLLER BEARING | *2 | DRIVE PINION COMPANION FLANGE OIL SEAL |
| *3 | DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY | *4 | NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY |
| *5 | NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY HOLE SNAP RING | *6 | NO. 1 TRANSFER THRUST BEARING RACE |
| *7 | NO. 2 TRANSFER THRUST BEARING RACE | *8 | TRANSFER EXTENSION HOUSING |
| *9 | TRANSFER EXTENSION HOUSING OIL SEAL | *10 | TRANSFER OUTPUT SHAFT CYLINDRICAL ROLLER BEARING |
| *11 | TRANSFER OUTPUT SHAFT SHIM | *12 | TRANSFER OUTPUT SHAFT WASHER |
| *13 | TRANSFER OUTPUT SHAFT NUT | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
MP grease |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | BREATHER OIL DEFLECTOR | *2 | REAR TRANSFER CASE |
| *3 | TRANSFER COUNTER GEAR ASSEMBLY | *4 | TRANSFER COUNTER GEAR BEARING |
| *5 | TRANSFER FRONT DRIVE GEAR ASSEMBLY | *6 | TRANSFER FRONT DRIVE GEAR ASSEMBLY CYLINDRICAL ROLLER BEARING |
| *7 | TRANSFER IDLER GEAR ASSEMBLY | *8 | TRANSFER IDLER GEAR BEARING |
| *9 | TRANSFER INPUT GEAR STOPPER | *10 | TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING |
| *11 | TRANSFER INPUT SHAFT | *12 | TRANSFER OIL SEAL RING |
| *13 | TRANSFER IDLER GEAR SHIM | *14 | TRANSFER COUNTER GEAR SHIM |
| *15 | NO. 3 TRANSFER THRUST BEARING RACE | *16 | TRANSFER COUNTER GEAR SHIM |
| *17 | NO. 3 TRANSFER THRUST BEARING RACE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | FORWARD CLUTCH DRUM OIL SEAL RING | *2 | NO. 1 TRANSFER OIL STRAINER |
| *3 | TRANSFER FRONT CASE OIL SEAL | *4 | TRANSFER FRONT DRIVE GEAR PIN |
| *5 | TRANSFER OIL PUMP DRIVE SHAFT | *6 | TRANSFER OIL PUMP PLATE SUB-ASSEMBLY |
| *7 | TRANSFER OIL SEPARATOR | *8 | TRANSFER OIL PUMP PLATE PIN |
| *9 | TRANSFER OIL PUMP DRIVE ROTOR | *10 | TRANSFER OIL PUMP DRIVEN ROTOR |
| *11 | FRONT TRANSFER CASE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |