ENGINE OIL COOLER REMOVAL

Note


  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

  • After removing the injection pipes, clean them with a brush and compressed air.


  1. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

      B007OT1E01
      Text in Illustration
      *1 Bleeder Plug *2 Radiator Reservoir Cap Sub-assembly
      *3 Radiator Reservoir Assembly *4 Cylinder Block Drain Cock Plug
      *5 Radiator Drain Cock Plug - -

    2. Remove the radiator reservoir cap sub-assembly.

    3. Loosen the cylinder block drain cock plug (on the engine oil cooler cover), and drain the engine coolant.

    4. Tighten the radiator drain cock plug.

    5. Tighten the cylinder block drain cock plug (on the engine oil cooler cover).

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Wipe the oil pan and oil pan drain plug.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  3. REMOVE EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY (w/ DPF)

    Click here

  4. REMOVE EGR COOLER ASSEMBLY (w/o DPF)

    Click here

  5. REMOVE STARTER ASSEMBLY (w/ DPF)


  6. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)


    1. B007R5UE01

      Disconnect the 3 fuel hoses.

    2. Remove the bolt and No. 2 injection pipe clamp from the No. 3 nozzle leakage pipe and No. 3 fuel pipe.

    3. Remove the fuel check valve and gasket.

    4. Remove the bolt and No. 3 nozzle leakage pipe.

  7. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)


    1. B007SXB

      Remove the 2 bolts and No. 2 exhaust manifold heat insulator.

  8. REMOVE NO. 3 FUEL PIPE (w/ DPF)

    Tech Tips

    It is not necessary to completely remove the No. 3 fuel pipe from the vehicle.


    1. for Engine LH Side:


      1. Using a 6 mm hexagon wrench, remove the union bolt and gasket.

      2. Remove the fuel check valve and gasket.

      3. Remove the bolt.

    2. for Engine Rear Side:


      1. Remove the union bolt and gasket.

      2. Remove the 2 bolts.

        B007ROKE01

  9. REMOVE FUEL INLET PIPE SUB-ASSEMBLY (w/o DPF)


    1. B007SVQE01

      Remove the bolt and No. 2 injection pipe clamp.

    2. Remove the bolt and detach the No. 1 injection pipe clamp.

      Note

      If a No. 1 injection pipe clamp is removed from the fuel inlet pipe, replace the No. 1 injection pipe clamp with a new one.

    3. B007RXX

      Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

  10. REMOVE VACUUM SWITCHING VALVE BRACKET (w/o DPF)


    1. B007U0B

      Disconnect the vacuum switching valve connector and 2 vacuum hoses.

    2. Remove the bolt and vacuum switching valve bracket.

  11. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/ DPF)


    1. B007TA0E01

      Remove the union bolt and gasket.

    2. Remove the 3 bolts and No. 2 nozzle leakage pipe.

  12. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY (w/o DPF)


    1. B007ROT

      Disconnect the 3 fuel hoses.

    2. B007V57E01

      Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.

  13. REMOVE NO. 4 WATER BY-PASS HOSE (w/ DPF)

    B007VS5

  14. REMOVE NO. 2 WATER BY-PASS HOSE (w/ DPF)

    B007SH2

  15. REMOVE OIL FILTER SUB-ASSEMBLY


    1. B007RH3E02

      Using SST, remove the oil filter.

      SST
      09228-07501

      Tech Tips


      • Position the drain oil container to collect the oil from the oil filter.

      • Insert cloth, etc. between the oil filter and oil cooler cover to prevent engine oil from dripping out.

      • When engine oil starts coming out of the oil filter, briefly stop loosening the oil filter to prevent engine oil from flowing out from the oil cooler cover.

  16. REMOVE OIL COOLER COVER SUB-ASSEMBLY


    1. w/ DPF:


      1. Disconnect the oil pressure sensor connector.

      2. Remove the drain cock plug.

      3. Disconnect the 2 vinyl tubes.

      4. B007UJU

        Remove the 2 nuts and bolt and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.

      5. B007QJI

        Remove the 12 bolts and oil cooler cover.

    2. w/o DPF:


      1. Disconnect the oil pressure switch connector.

      2. Disconnect the 2 vinyl tubes.

      3. B007OEC

        Remove the 2 nuts and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.

      4. Remove the 13 bolts and oil cooler cover.

  17. REMOVE OIL COOLER ASSEMBLY


    1. B007QT9E01

      Loosen the 4 nuts.

    2. Partially tap out the oil cooler by tapping each nut head with a plastic-faced hammer.

    3. Remove the 4 nuts, oil cooler and 2 gaskets.

  18. REMOVE OIL FILTER RECEIVER (w/ DPF)


    1. Remove the 2 bolts and oil filter receiver from the oil cooler cover.