ENTRY AND START SYSTEM(for Start Function) OPERATION CHECK

OPERATION DESCRIPTION

Note:

Make sure that the entry and start system (for Start Function) has not been canceled before performing this inspection.

Push-button start function: (for Multi-Mode Manual Transaxle)

When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is depressed, the engine is started by pressing the engine switch.
When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.

*a	Smart Warning Light Blinks (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC) and the smart warning light blinks (green) in the combination meter assembly.

*a	Smart Warning Light Blinks (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG) and the smart warning light blinks (green) in the combination meter assembly.

*a	Smart Warning Light Illuminates (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the brake pedal is depressed while the shift lever is in N, the smart warning light illuminates (green).

The engine will start if the engine switch is pressed when the smart warning light is illuminated (green).

Push-button start function: (for Manual Transaxle)

When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the clutch pedal is depressed, the engine is started by pressing the engine switch.
When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the clutch pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.

*a	Smart Warning Light Blinks (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed while not depressing the clutch pedal, the power source mode changes to on (ACC) and the smart warning light blinks (green) in the combination meter assembly.

*a	Smart Warning Light Blinks (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed 2 times without depressing the clutch pedal, the power source mode changes to on (IG) and the smart warning light blinks (green) in the combination meter assembly.

*a	Smart Warning Light Illuminates (Green)

After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the clutch pedal is depressed, the smart warning light illuminates (green).

The engine will start if the engine switch is pressed when the smart warning light is illuminated (green).

Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion: (for Multi-Mode Manual Transaxle)

Unlock the door using the mechanical key built into the electrical key transmitter sub-assembly and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

*a	Smart Warning Light Blinks (Green)

A buzzer sounds and the smart warning light blinks (green) in the combination meter assembly, and the power source mode changes to on (IG).

Pressing the engine switch without depressing the brake pedal changes the power source mode from on (IG) to off.

Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion: (for Manual Transaxle)

Unlock the door using the mechanical key built into the electrical key transmitter sub-assembly and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the clutch pedal and facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

*a	Smart Warning Light Blinks (Green)

A buzzer sounds and the smart warning light blinks (green) in the combination meter assembly, and the power source mode changes to on (IG).

Pressing the engine switch without depressing the clutch pedal changes the power source mode from on (IG) to off.

Starting the engine when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion: (for Multi-Mode Manual Transaxle)

Unlock the door using the mechanical key built into the electrical key transmitter sub-assembly and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the brake pedal with the shift lever in N and facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

*a	Smart Warning Light Blinks (Green)

A buzzer sounds and the smart warning light blinks (green) in the combination meter assembly, and the power source mode changes to on (IG).

Press the engine switch with the brake pedal depressed to start the engine.

Starting the engine when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion: (for Manual Transaxle)

Unlock the door using the mechanical key built into the electrical key transmitter sub-assembly and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the clutch pedal and facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

*a	Smart Warning Light Blinks (Green)

A buzzer sounds and the smart warning light blinks (green) in the combination meter assembly, and the power source mode changes to on (IG).

Press the engine switch with the clutch pedal depressed to start the engine.

CHECK PUSH-BUTTON START FUNCTION

Check the push-button start function: (for Multi-Mode Manual Transaxle)

*a	Smart Warning Light Illuminates (Green)

Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off. With the shift lever in N, check that the smart warning light in the combination meter assembly illuminates (green) when the brake pedal is depressed. Then check that the engine starts when the engine switch is pressed after the smart warning light in the combination meter assembly illuminates (green).

While the brake pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the engine switch is pressed: off → on (ACC) → on (IG) → off.

Tip:
When the engine switch is pressed with the engine switch on (IG) and the shift lever not in N, the power source mode does not change to off, but changes to on (ACC).
Check that the steering lock operates when a door is opened.

Tip:
When the engine switch is pressed after the vehicle is stopped, the engine stops and all the power turns off. However, if the shift lever is not in N when the engine switch is pressed with the vehicle stopped, the power source mode will not change to off, but will change to on (ACC).

*a	Inspection Point

Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

Note:

Even if the electrical key transmitter sub-assembly is in a vehicle interior key detection area, the electrical key transmitter sub-assembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in a door pocket or the glove box, on the floor or in a storage compartment.

Tip:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.
Perform this inspection for both inspection points.

*a	Inspection Point

Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

Note:

Tip:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat.
Perform this inspection for both inspection points.

Check the push-button start function: (for Manual Transaxle)

*a	Smart Warning Light Illuminates (Green)

Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off. Check that the smart warning light in the combination meter assembly illuminates (green) when the clutch pedal is depressed. Then check that the engine starts when the engine switch is pressed after the smart warning light in the combination meter assembly illuminates (green).

While the clutch pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the engine switch is pressed: off → on (ACC) → on (IG) → off.
Check that the steering lock operates when a door is opened.

*a	Inspection Point

Note:

Tip:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.
Perform this inspection for both inspection points.

*a	Inspection Point

Note:

Tip:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat.
Perform this inspection for both inspection points.

CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION
1. Check the transmitter battery saving mode function:
  1. Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
  2. Check that the entry and start system (for Start Function) does not operate while in transmitter battery saving mode.
    
    Tip:
    To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.

CHECK POWER SOURCE MODE CHANGING FUNCTION

Check the engine switch.

for Multi-Mode Manual Transaxle:

Check that the power source mode changes according to the chart below.


Shift Position	Brake Pedal	Power Source Mode when Engine Switch Pressed
N	Depressed	Off → engine starts
N	Depressed	On (ACC) → engine starts
N	Depressed	On (IG) → engine starts
N	Depressed	Engine running → off
All	Released	Off → on (ACC) → on (IG) → off
All	Released	Engine running → off
Not N	Depressed	Off → on (IG)
Not N	Depressed	On (ACC) → on (IG)
Not N	Depressed	Engine running → off

for Manual Transaxle:

Check that the power source mode changes according to the chart below.


Clutch Pedal	Power Source Mode when Engine Switch Pressed
Released	Off → on (ACC) → on (IG) → off
Released	Engine running → off
Depressed	Off → engine starts
Depressed	On (ACC) → engine starts
Depressed	On (IG) → engine starts
Depressed	Engine running → off

CHECK POWER SOURCE MODE INDICATION

*a	Smart Warning Light

Check the smart warning.

Table 1. Indicator Inspection
Power Source Mode	Indicator
Off (Excluding condition in which the engine can be started)	Off
On (ACC) (Excluding condition in which the engine can be started)	Blinks (green)
On (IG) (Excluding condition in which the engine can be started)	Blinks (green)
Condition in which engine can be started*1	Illuminates (green)
Engine started	Off

Tip:

*1: Indicates the condition in which the engine can be started by pressing the engine switch while all of the following conditions are met:

for Multi-Mode Manual Transaxle:
Key is verified*2 or the immobiliser is unset (engine switch is on (ACC) or on (IG)).
The stop light switch is on.
The shift lever is in N.

for Manual Transaxle:
Key is verified*2 or the immobiliser is unset (engine switch is on (ACC) or on (IG)).
The clutch start switch is on.
The stop and start system is not prohibiting starting of the engine due to the engine hood being opened while the engine was stopped by the stop and start system. (w/ Stop and Start System)

*2: When the electrical key transmitter sub-assembly is in the cabin, the ID code sent as a result of communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the cabin.