AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) DATA LIST / ACTIVE TEST
DATA LIST
Tip:Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus:
Body / Air Conditioner / Data List.
Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
Table 1. Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Ambient Temp Sensor
Ambient temperature sensor /
Min.: -23.3°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed
-
Adjusted Ambient Temp
Adjusted ambient temperature
/ Min.: -30.8°C (-23.44°F)
Max.: 50.8°C (123.44°F)
Adjusted ambient temperature displayed
-
Evaporator Fin Thermistor
No. 1 cooler thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed
-
Evaporator Target Temp
Target evaporator temperature /
Min.: -327.68°C (-557.82°F)
Max.: 327.67°C (621.81°F)
Target evaporator temperature displayed
-
Engine Coolant Temp
Engine coolant temperature /
Min.: 1.3°C (34.34°F)
Max.: 90.55°C (194.99°F)
Actual engine coolant temperature displayed
-
Regulator Pressure Sensor
Refrigerant pressure sensor /
Min.: -0.4566 MPa
Max.: 3.2943 MPa
Actual refrigerant pressure displayed
-
Regulator Control Current
Compressor assembly with pulley / Min.: 0, Max.: 0.997
Value changes between 0 A and 0.997 A in accordance with compressor assembly with pulley operation
-
Electric Heater Count
Electric (PTC) heater count / Min.: 0, Max.: 3
Actual number of the heater elements to be heated is displayed
-
Number of Trouble Codes
Number of trouble codes / Min.: 0, Max.: 255
Number of DTCs displayed
-
Table 2. Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/C Signal
A/C signal / ON or OFF
ON: A/C switch on
OFF: A/C switch off
-
ACTIVE TEST
Tip:Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Table 3. Air Conditioner Tester Display
Test Part
Control Range
Diagnostic Note
Heater Active Level*
Heater level
Min.: 0, Max.: 3
-
Magnetic Clutch Relay
Magnet clutch relay operation
ON or OFF
-
*: w/ PTC Heater