AIR CONDITIONING SYSTEM, Diagnostic DTC:B14B2

DTC Code DTC Name
B14B2 Lost Communication with Front Panel LIN

DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B14B2 Lost Communication with Front Panel LIN Lost communication with the air conditioning control assembly.

  • Harness or connector

  • LIN communication system

  • Air conditioning control assembly

  • Air conditioning amplifier assembly

 Memorized (10 seconds or more) -

Tech Tips

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

WIRING DIAGRAM

B0059KLE01

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

    Click here

Tech Tips

w/ Stop and Start System:

The audio and visual system troubleshooting procedure is based on the premise that the stop and start system is operating normally. Check the audio and visual system first before troubleshooting the audio and visual system.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BATTERY AND BODY GROUND)


    1. B008J7PC05
      *a

      Front view of wire harness connector

      (to Air Conditioning Control Assembly)

      Disconnect the air conditioning control assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I13-8 (IG+) - Body ground Engine switch off Below 1 V
      Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2
      *1: w/o Stop and Start System
      *2: w/ Stop and Start System

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I13-14 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Disconnect the I13 air conditioning control assembly connector.

    2. Disconnect the I50 air conditioning amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I13-6 (LIN1) - I50-37 (LIN1) Always Below 1 Ω
      I13-6 (LIN1) or I50-37 (LIN1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK AIR CONDITIONING CONTROL ASSEMBLY


    1. Replace the air conditioning control assembly.

      Click here

    2. Check the air conditioning control assembly operates normally.

      Tech Tips

      Since the air conditioning control assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning control assembly with a new or known good one and check that the condition returns to normal.

      OK
      Air conditioning control assembly operation returns to normal.
      Result
      Result Proceed to
      OK A
      NG (When troubleshooting according to Problem Symptoms Table) B
      NG (When troubleshooting according to the DTC) C

    A

    END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here