AUTOMATIC TRANSAXLE SYSTEM

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tip:

  • The TCM of this system is connected to the CAN communication system. Therefore, before starting troubleshooting, be sure to check that there is no trouble in the CAN communication system.

  • *: Use the GTS.

PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

    Result

    Proceed to

    NEXT
    NEXT

  2. CUSTOMER PROBLEM ANALYSIS

    1. Refer to How to Troubleshoot ECU Controlled Systems in the Introduction section.

      Click hereClick hereClick hereClick hereClick hereClick here

    Result

    Proceed to

    NEXT
    NEXT

  3. INSPECT BATTERY VOLTAGE

    Standard voltage

    11 to 14 V

    If the voltage is below 11 V, recharge or replace the battery before proceeding.

    Result

    Proceed to

    NEXT
    NEXT

  4. CONNECT GTS TO DLC3*

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK AND CLEAR DTCS AND FREEZE FRAME DATA*

    1. Refer to DTC Check/Clear.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  6. VISUAL INSPECTION

    Result

    Proceed to

    NEXT
    NEXT

  7. SELECT CHECK MODE AND PERFORM DIAGNOSIS*

    1. Refer to Check Mode Procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  8. PROBLEM SYMPTOM CONFIRMATION

    1. Refer to Road Test.

      Click here

    Result

    Result

    Proceed to

    Symptom does not occur

    A

    Symptom occurs

    B
    B

    DTC CHECK*Click here

    A

  9. SYMPTOM SIMULATION

    1. Refer to Electronic Circuit Inspection Procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  10. DTC CHECK*

    1. Refer to DTC Check/Clear.

      Click here

    Result

    Result

    Proceed to

    DTC is not output

    A

    DTC is output

    B
    B

    DTC CHARTClick here

    A

  11. BASIC INSPECTION

    1. Refer to Park/Neutral Position Switch.

      Click here

    2. Refer to Shift Lever.

      Click here

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACEClick here

    OK

  12. MECHANICAL SYSTEM TESTS*

    1. Refer to Mechanical System Test.

      Click here

    Result

    Result

    OK

    NG
    NG

    COMPONENT INSPECTIONClick here

    OK

  13. HYDRAULIC TEST*

    1. Refer to Hydraulic Test.

      Click here

    Result

    Result

    OK

    NG
    NG

    COMPONENT INSPECTIONClick here

    OK

  14. MANUAL SHIFTING TEST

    1. Refer to Manual Shifting Test.

      Click here

    Result

    Result

    OK

    NG
    NG

    PROBLEM SYMPTOMS TABLE CHAPTER 2Click here

    OK

  15. PROBLEM SYMPTOMS TABLE CHAPTER 1

    1. Refer to Problem Symptoms Table.

      Click hereClick here

    Result

    Result

    OK

    NG
    NG

    CIRCUIT INSPECTIONClick here

    OK

  16. PROBLEM SYMPTOMS TABLE CHAPTER 2

    1. Refer to Problem Symptoms Table.

      Click hereClick here

    Result

    Result

    NEXT
    NEXT

  17. COMPONENT INSPECTION

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACEClick here

    OK

  18. DTC CHART

    1. Refer to Diagnostic Trouble Code Chart.

      Click hereClick here

    Result

    Result

    NEXT
    NEXT

  19. CIRCUIT INSPECTION

    Result

    Result

    NEXT
    NEXT

  20. IDENTIFICATION OF PROBLEM

    Result

    Result

    NEXT
    NEXT

  21. REPAIR OR REPLACE

    Result

    Result

    NEXT
    NEXT

  22. CONFIRMATION TEST

    Result

    Result

    NEXT
    NEXT

    END