AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System), Diagnostic DTC:B1411

DTC Code DTC Name
B1411 Room Temperature Sensor Circuit

DESCRIPTION

The cooler (room temp. sensor) thermistor is installed in the instrument panel to detect the cabin temperature, which is used to control the air conditioning system. The resistance of the cooler (room temp. sensor) thermistor changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the cooler (room temp. sensor) thermistor and reads voltage changes due to changes in the resistance of the cooler (room temp. sensor) thermistor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1411 Room Temperature Sensor Circuit Open or short in room temperature sensor circuit

  • Cooler (room temp. sensor) thermistor

  • Harness or connector

  • Air conditioning amplifier assembly

Memorized

(4 sec. or more)*

Tech Tips

If the cabin temperature is approximately -18.6°C (-1.48°F) or lower, DTC B1411 may be stored even though the system is normal.

WIRING DIAGRAM

B0086HFE01
*a Cooler (Room Temp. Sensor) Thermistor
*b Air Conditioning Amplifier Assembly

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Air Conditioner > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Room Temperature Sensor Cooler (room temp. sensor) thermistor

      Min.: -6.50°C (20.30°F)

      Max.: 57.25°C (135.05°F)

      		 Actual cabin temperature displayed

      Cooler (room temp. sensor) thermistor circuit malfunction


      • When open circuit: -6.50°C (20.30°F)

      • When short circuit: 57.25°C (135.05°F)

      Body Electrical > Air Conditioner > Data List
      Tester Display
      Room Temperature Sensor
      OK
      The display is as specified in the normal condition column.
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

  2. INSPECT COOLER (ROOM TEMP. SENSOR) THERMISTOR


    1. Remove the cooler (room temp. sensor) thermistor.

      Click here

    2. Inspect the cooler (room temp. sensor) thermistor.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE COOLER (ROOM TEMP. SENSOR) THERMISTOR Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (COOLER (ROOM TEMP. SENSOR) THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Disconnect the K55 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K67-1 (+) - K55-14 (TR) Always Below 1 Ω
      K67-2 (-) - K55-1 (SG-1) Always Below 1 Ω
      K67-1 (+) or K55-14 (TR) - Other terminals and body ground Always 10 kΩ or higher
      K67-2 (-) or K55-1 (SG-1) - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR