EMISSION CONTROL SYSTEM(w/ Canister Pump Module) ON-VEHICLE INSPECTION

CAUTION / NOTICE / HINT

CAUTION:

To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).

B007ZAW

PROCEDURE


  1. VISUALLY CHECK HOSES, CONNECTIONS AND GASKETS


    1. Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

      Note


      • Detachment or other problems with the engine oil level dipstick, oil filler cap sub-assembly, ventilation hose or other components may cause the engine to run improperly.

      • Air suction caused by disconnections, looseness or cracks in any part of the air induction system between the throttle body with motor assembly and cylinder head sub-assembly will cause engine failure or engine malfunctions.

      If any defects are found, replace parts as necessary.

  2. INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

    CAUTION:

    To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).


    1. Connect the GTS to the DLC3.

    2. B007ZG8

      Slide the clip and disconnect the No. 2 fuel vapor feed hose assembly from the purge valve (purge VSV).

    3. Start the engine.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.


      Powertrain > Engine > Active Test
      Tester Display
      Activate the EVAP Purge VSV

    6. Check that vacuum occurs at the purge valve (purge VSV) port.

    7. If vacuum does not occur, check the following items.


      • Purge valve (purge VSV)

      • Clogs in the fuel vapor feed hose connecting the intake manifold and purge valve (purge VSV)

      • Voltage from the ECM PRG terminal

        Click here

    8. Exit Active Test mode, connect the No. 2 fuel vapor feed hose assembly to the purge valve (purge VSV) and slide the clip to secure it.

      Click here

      If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.

    9. Enter the following menus: Powertrain / Engine / Data List / EVAP (Purge) VSV.


      Powertrain > Engine > Data List
      Tester Display
      EVAP (Purge) VSV

    10. Warm up the engine and drive the vehicle.

    11. Confirm that the purge valve (purge VSV) opens.

      If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.

  3. INSPECT EJECTOR

    CAUTION:

    To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).


    1. Slide the clip and disconnect the No. 3 ventilation hose from the cylinder head cover sub-assembly.

    2. B007XB3C03
      *a Pin
      *b Valve
      *c Ejector

      Check the operation of the valve.


      1. Insert the pin into the ejector hole and check that the valve moves smoothly.

        OK
        The valve moves smoothly.

        Tech Tips

        If the valve does not move smoothly, it may be stuck inside the ejector.

    3. Connect the No. 3 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

  4. CHECK FUEL TANK AND VENT LINE


    1. Disconnect the vent line hose from the canister (charcoal canister assembly).

      B007Y96C01
      *1 Fuel Tank Cap Assembly *2 Vent Line Hose
      *a Pressure Gauge - -

    2. Connect a pressure gauge to the vent line hose.

    3. Apply 4 kPa (0.04 kgf/cm2, 0.6 psi) of pressure to the vent line of the fuel tank assembly.

      Tech Tips

      Perform this inspection with the fuel tank assembly less than 90% full. When the fuel tank assembly is full, the fuel fill check valve closes and the pressure is released through the 2 mm (0.0787 in.) orifice. As a result, when the fuel tank cap assembly is removed, the pressure does not decrease smoothly.

    4. Check that the fuel tank assembly pressure is maintained for some time and does not decrease immediately.

      Tech Tips

      If the pressure decreases immediately, one of the following may apply:


      • The fuel tank cap assembly is not completely tightened.

      • The fuel tank cap assembly is damaged.

      • Air is leaking from the vent line.

      • The fuel tank assembly is damaged.

    5. Remove the fuel tank cap assembly and check that the pressure is released smoothly.

      If the pressure is not released smoothly, replace the fuel tank assembly.

    6. Reconnect the vent line hose to the canister (charcoal canister assembly).

  5. INSPECT AIR LINE


    1. B007XPEC01
      *1 Air Line Tube
      *a Air

      Disconnect the air line tube from the charcoal canister leak detection pump sub-assembly.

    2. Check that air flows freely into the air line.

      If air does not flow freely into the air line, repair or replace the air line tube.

    3. Connect the air line tube to the charcoal canister leak detection pump sub-assembly.