ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch OFF.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch ON.

    5. Turn the intelligent tester ON.

    6. Enter the following menus: Powertrain / ECT / Data List.

    7. Follow the instructions on the tester and read the Data List.

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed

      Vehicle speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual vehicle speed Speed indicated on speedometer
      Engine Speed

      Engine speed/

      Min.: 0 rpm

      Max.: 16383.75 rpm

      		 Engine idling: 700 to 800 rpm -
      Calculate Load

      Calculated load by ECM/

      Min.: 0%

      Max.: 100%

      		 Running without load (2500 rpm): 13.1 to 18.9% -
      Coolant Temp

      Engine coolant temperature/

      Min.: -40°C (-40°F)

      Max.: 140°C (284°F)

      		 After warming up engine: 80 to 90°C (176 to 194°F)

      • If the value is -40°C (-40°F), the sensor circuit is open.

      • If the value is 140°C (284°F), the sensor circuit is shorted.
      Engine Run Time

      Engine run time/

      Min.: 0 seconds,

      Max.: 65535 seconds

      		 Time after engine start -
      Battery Voltage

      Battery voltage/

      Min.: 0 V

      Max.: 65.535 V

      		 Engine idling: 11 to 14 V -
      Starter Signal

      Starter signal/

      ON or OFF

      • ON: Engine cranking

      • OFF: Engine not cranking

      		 -
      Neutral Position SW Signal

      PNP switch status/

      ON or OFF

      Shift lever is:

      On P or N: ON

      Not on P or N: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      Stop Light Switch

      Stop light switch status/

      ON or OFF

      • Brake pedal is depressed: ON

      • Brake pedal is released: OFF

      		 -
      Check Mode

      Check mode/

      ON or OFF

      		 ON: Check mode ON -
      SPD Test Result

      Check mode result for vehicle/

      Compl or Incmpl

      		 - -
      Complete Parts Monitor

      Comprehensive component monitor/

      Not Avl or Avail

      		 - -
      Fuel System Monitor

      Fuel system monitor/

      Not Avl or Avail

      		 - -
      Misfire Monitor

      Misfire monitor/

      Not Avl or Avail

      		 - -
      EGR/VVT Monitor

      EGR/VVT monitor/

      Not Avl or Avail

      		 - -
      EGR/VVT Monitor

      EGR/VVT monitor/

      Compl or Incmpl

      		 - -
      O2S(A/FS) Heater Monitor

      Heated oxygen sensor (air fuel ratio sensor) heater monitor/

      Not Avl or Avail

      		 - -
      O2S(A/FS) Heater Monitor

      Heated oxygen sensor (air fuel ratio sensor) heater monitor/

      Compl or Incmpl

      		 - -
      O2S(A/FS) Monitor

      Heated oxygen sensor (air fuel ratio sensor) monitor/

      Not Avl or Avail

      		 - -
      O2S(A/FS) Monitor

      Heated oxygen sensor (air fuel ratio sensor) monitor/

      Compl or Incmpl

      		 - -
      A/C Monitor

      A/C monitor/

      Not Avl or Avail

      		 - -
      A/C Monitor

      A/C monitor/

      Compl or Incmpl

      		 - -
      2nd Air Monitor

      2nd air monitor/

      Not Avl or Avail

      		 - -
      2nd Air Monitor

      2nd air monitor/

      Compl or Incmpl

      		 - -
      EVAP Monitor

      EVAP monitor/

      Not Avl or Avail

      		 - -
      EVAP Monitor

      EVAP monitor/

      Compl or Incmpl

      		 - -
      Heated Catalyst Monitor

      Heated catalyst monitor/

      Not Avl or Avail

      		 - -
      Heated Catalyst Monitor

      Heated catalyst monitor/

      Compl or Incmpl

      		 - -
      Catalyst Monitor

      Catalyst monitor/

      Not Avl or Avail

      		 - -
      Catalyst Monitor

      Catalyst monitor/

      Compl or Incmpl

      		 - -
      # Codes (Include History)

      # of Codes/

      Min.: 0

      Max.: 255

      		 - Number of detected DTCs
      MIL

      MIL status/

      ON or OFF

      		 ON: MIL ON -
      MIL ON Run Distance

      MIL ON run distance/

      Min.: 0 km (0 mile)

      Max.: 65535 km (40723 mile)

      		 Distance after DTC stored -
      Running Time from MIL ON

      Running time from MIL on/

      Min.: 0 minutes,

      Max.: 65535 minutes

      		 Equivalent to running time after MIL turns on -
      Time after DTC Cleared

      Time after DTC cleared/

      Min.: 0 minutes,

      Max.: 65535 minutes

      		 Equivalent to time after DTCs cleared -
      Distance from DTC Cleared

      Distance after DTC cleared/

      Min.: 0 km (0 mile)

      Max.: 65535 km (40723 mile)

      		 Equivalent to distance driven after DTCs cleared -
      Warmup Cycle Cleared DTC

      Warm-up cycle after DTC cleared/

      Min.: 0, Max.: 255

      		 - Number of warm-up cycles after DTCs cleared
      Number of Emission DTC Number of emission DTCs - -
      Model Code Model Code/ - -
      Engine Type Engine Type/ - -
      Cylinder Number Cylinder number/ - -
      Destination Destination/ - -
      Model Year Model year/ - -
      Engine Speed from EFI

      Engine speed/

      Min.: 0 rpm

      Max.: 16383.75 rpm

      		 - Engine speed received from the ECM.
      Intake-Air Temp from EFI

      Intake air temperature/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      		 - Intake air temperature received from the ECM.
      Coolant Temp from EFI

      Engine coolant temperature/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      		 - Coolant temperature received from the ECM.
      Accel Position from EFI

      Absolute accelerator pedal position/

      Min.: 0%

      Max.: 100%

      		 - -
      Injection Volume from EFI

      Injection volume/

      Min.: -10 mm3

      Max.: 1,279.98 mm3

      		- -
      SPD (NC0)

      Input turbine speed/

      Min.: 0 rpm

      Max.: 12750 rpm

      • Lock-up ON (warmed up engine, other than O/D):

        Input turbine speed (NC0) is equal to the engine speed

      • Lock-up ON (warmed up engine, O/D):

        Input turbine speed (NC0) is 0 rpm

      • Lock-up OFF (idling with shift lever on N):

        Input turbine speed (NC0) is nearly equal to engine speed

      		 -
      SPD (SP2)

      Output shaft speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      Vehicle stopped: 0 km/h (0 mph)

      (output shaft speed is equal to vehicle speed)

      		 -
      Shift SW Status (R Range)

      PNP switch status/

      ON or OFF

      Shift lever is:

      On R: ON

      Not on R: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      Shift SW Status (2 Range)

      PNP switch status/

      ON or OFF

      Shift lever is:

      On 2: ON

      Not on 2: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      Shift SW Status (L Range)

      PNP switch status/

      ON or OFF

      Shift lever is:

      On L: ON

      Not on L: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      Shift SW Status (D Range)

      PNP switch status/

      ON or OFF

      Shift lever is:

      On D: ON

      Not on D: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      Shift SW Status (3 Range)

      PNP switch status/

      ON or OFF

      Shift lever is:

      On 3: ON

      Not on 3: OFF

      When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

      Tech Tips

      When failure still occurs even after adjusting these parts, Click here, Click here

      A/T Oil Temperature 3

      ATF temperature sensor value/

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      • After stall test:

        Approximately 80°C (176°F)

      • Equal to ambient temperature during engine is cold

      		 If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited
      Lock Up

      Lock-up/

      ON or OFF

      • ON: Lock-up operating

      • OFF: Lock-up not operating

      		 -
      Lock Up Solenoid Status

      Lock-up solenoid status/

      ON or OFF

      • Lock-up: ON

      • Not on lock-up: OFF

      		 -
      Shift Status

      ECM gear shift command/

      1st, 2nd, 3rd or 4th (O/D)

      Shift lever position is:


      • On L: 1st

      • On 2: 1st or 2nd

      • On D (O/D OFF): 1st, 2nd or 3rd

      • On D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)

      		 -
      SLT Solenoid Status

      Shift solenoid SLT status/

      ON or OFF

      • Accelerator pedal is depressed: OFF

      • Accelerator pedal is released: ON

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

    The Data List can be displayed during the Active Test.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON.

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / ECT / Active Test.

    5. Perform the Active Test.

      Tester Display Test Part Control Range Diagnostic Note
      Connect the TC and TE1 Turn on and off TC and TE1 connection ON or OFF -
      Activate the Solenoid (SLT)* Operate shift solenoid valve SLT and raise line pressure

      ON or OFF

      Tech Tips


      • OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)

      • ON: No action (normal operation)

      [Vehicle Condition]


      • Vehicle stopped

      • Engine idling
      Activate the Solenoid (S1) Operate shift solenoid valve S1 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Solenoid (S2) Operate shift solenoid valve S2 ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Activate the Lock Up Control shift solenoid valve SLT to set automatic transmission to lock-up ON or OFF

      Possible to check shift solenoid valve SLT operation.

      [Vehicle Condition]


      • Throttle valve opening angle: Less than 35%

      • Vehicle speed: 60 km/h (37 mph) or more
      Activate the Solenoid (SL) Operate shift solenoid valve SL ON or OFF

      [Vehicle Condition]


      • Engine stopped

      • Shift lever in P or N
      Control the Shift Position Operate shift solenoid valves and set each shift position

      • Press "→" button: Shift up

      • Press "←" button: Shift down

      Possible to check operation of the shift solenoid valves.

      [Vehicle Condition]

      50 km/h (31 mph) or less

      Tech Tips

      *: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test Click here as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.