ENTRY AND START SYSTEM(for Entry Function) Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment

DESCRIPTION

When the entry luggage compartment open function does not operate, one of the following may be the cause: 1) a luggage compartment door opener switch malfunction; 2) a luggage compartment door opener system malfunction; 3) a communication malfunction between electrical key oscillator and electrical key transmitter; or 4) a certification ECU malfunction.

WIRING DIAGRAM

A004P78E02

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (KEY CANCEL SWITCH)


    1. Using the intelligent tester, read the Data List.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Auto Entry Cancel SW Entry function cancel/ON or OFF Mode status displayed -
      Result
      Result Proceed to
      Entry function cancel is OFF A
      Entry function cancel is ON B

    B

    PERFORM CANCELLATION OF ENTRY KEY CANCEL FUNCTION

    A

  2. CHECK LUGGAGE DOOR OPENER OPERATION


    1. When the luggage compartment door opener switch is operated, check that the luggage compartment door opens.

      Result
      Result Proceed to
      Luggage compartment door opens A
      Luggage compartment door does not open B

    B

    GO TO LUGGAGE COMPARTMENT DOOR OPENER SYSTEM Click here

    A

  3. READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR OPENER SWITCH)


    1. Using the intelligent tester read the Data List.

      Entry&Start
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Tr/B-Door Unlock SW Luggage compartment door opener switch / ON or OFF

      ON: Luggage compartment door opener switch pushed

      OFF: Luggage compartment door opener switch not pushed

      		 -
      OK
      On tester screen, item changes between ON and OFF according to above chart.

    NG

    INSPECT LUGGAGE COMPARTMENT DOOR OPENER SWITCH Click here

    OK

  4. CHECK WAVE ENVIRONMENT


    1. A004OJYE02
      *1 Approximately 0.3 m
      *2 Vehicle Center

      Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the outside electrical key oscillator (in rear bumper) and perform an entry luggage compartment open function check.

      Note

      If the key is brought within 0.2 m (0.656 ft) of the rear bumper, communication is not possible.

      Tech Tips


      • When the electrical key transmitter is brought near the electrical key oscillator, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.


    OK

    AFFECTED BY WAVE INTERFERENCE

    NG

  5. KEY DIAGNOSTIC MODE


    1. A004RC4E02
      *1 0.7 to 1.0 m
      *2 Vehicle Center

      Diagnostic mode inspection (electrical key oscillator).


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry&Start / Key Communication Check / Overhead + Luggage.

      5. When the electrical key transmitter is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the outside electrical key oscillator (in rear bumper), check that the wireless door lock buzzer sounds.

        Tech Tips

        If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

        OK
        Wireless door lock buzzer sounds.

    OK

    REPLACE CERTIFICATION ECU

    NG

  6. CHECK HARNESS AND CONNECTOR (OUTSIDE ELECTRICAL KEY OSCILLATOR - CERTIFICATION ECU)

    A004T93E01
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Outside Electrical Key Oscillator (Outside Luggage))
    *2

    Front view of wire harness connector

    (to Certification ECU)

    1. Disconnect the H19 oscillator connector.

    2. Disconnect the D59 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D59-19 (CLG8) - H19-1 (CLG5) Always Below 1 Ω
      D59-20 (CG8B) - H19-2 (CLGB) Always Below 1 Ω
      D59-19 (CLG8) - Body ground Always 10 kΩ or higher
      D59-20 (CG8B) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT OUTSIDE ELECTRICAL KEY OSCILLATOR

    A004MQOE01
    Text in Illustration
    *1

    Component without harness connected

    (Outside Electrical Key Oscillator (Outside Luggage))

    1. Remove the outside electrical key oscillator (outside luggage) Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (CLG5) - 2 (CLGB) Always Below 1 Ω

    OK

    REPLACE CERTIFICATION ECU

    NG

    REPLACE OUTSIDE ELECTRICAL KEY OSCILLATOR (OUTSIDE LUGGAGE) Click here

  8. INSPECT LUGGAGE COMPARTMENT DOOR OPENER SWITCH

    A004RINE18

    1. Remove the luggage compartment door opener switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition

      1 (UL) - 2 (L)

      3 (B) - 2 (L)

      		 No switch 10 kΩ or higher
      1 (UL) - 2 (L) Lock switch pushed Below 1 Ω
      3 (B) - 2 (L) Open switch pushed Below 1 Ω

    NG

    REPLACE LUGGAGE COMPARTMENT DOOR OPENER SWITCH Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT DOOR OPENER SWITCH - CERTIFICATION ECU)

    A004R51E01
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Luggage Compartment Door Opener Switch)
    *2

    Front view of wire harness connector

    (to Certification ECU)

    1. Disconnect the G34 switch connector.

    2. Disconnect the D54 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G34-3 (B) - D54-22 (TSW5) Always Below 1 Ω
      G34-3 (B) - Body ground Always 10 kΩ or higher

    OK

    REPLACE CERTIFICATION ECU

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR