SFI SYSTEM, Diagnostic DTC:P008800

DTC Code DTC Name
P008800 Fuel Rail / System Pressure - Too High

DESCRIPTION

Refer to DTC P008700.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P008800 Fuel Rail / System Pressure - Too High

Although the ECM is requesting the fuel pump assembly (for high pressure side) to open the spill control valve, fuel pressure increases 3 MPa (30.6 kgf/cm2, 435 psi) from target pressure for about 10 seconds (1 trip detection logic).

  • Fuel pump assembly (for high pressure side)

  • Fuel pressure sensor (for high pressure side)

  • ECM

 Comes on DTC stored SAE Code: P0088

MONITOR DESCRIPTION

If the fuel pressure increases despite a decrease request signal being sent to the fuel pump assembly (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor (for high pressure side)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Record the Freeze Frame Data.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) and turn the GTS on.

  7. Start the engine.

  8. Based on the engine speed, engine load and other conditions displayed in the freeze frame data, reproduce the conditions present when the DTC was stored.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P008800.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008800)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine / Trouble Codes.

    4. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P008800 is output A
      DTC P008800 and other DTCs are output B

      Tech Tips

      If any DTCs other than P008800 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)


    1. Connect the GTS to the DLC3.

    2. Start the engine and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).


      Powertrain > Engine > Data List
      Tester Display
      Fuel Pressure (High)

    4. According to the display on the GTS, read the Data List while racing the engine.

      OK
      Fuel pressure fluctuates.
      Result
      Proceed to
      OK
      NG

      Tech Tips

      Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).

      Click here


    NG

    REPLACE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH (FUEL PRESSURE SENSOR (FOR HIGH PRESSURE SIDE)) Click here

    OK

  3. REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)


    1. Replace the fuel pump assembly (for high pressure side).

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008800 IS OUTPUT AGAIN)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    7. Enter the following menus: Powertrain / Engine / Trouble Codes.

    8. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P008800 is output B

    A

    END

    B

    REPLACE ECM Click here