AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM, Diagnostic DTC:B2416, B241A

DTC Code DTC Name
B2416 Height Control Sensor Malfunction
B241A Rear Height Control Sensor

DESCRIPTION

This DTC is stored when the headlight light control ECU sub-assembly LH detects a malfunction in the rear height control sensor sub-assembly LH power source or rear height control sensor sub-assembly LH.

The headlight light control ECU sub-assembly LH outputs DTC B2416 and B241A.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2416 Height Control Sensor Malfunction

  • Malfunction in rear height control sensor sub-assembly

  • Open or short in rear height control sensor sub-assembly power source circuit

  • Rear height control sensor sub-assembly LH

  • Headlight light control ECU sub-assembly LH

  • Harness or connector
B241A Rear Height Control Sensor

  • Malfunction in rear height control sensor sub-assembly LH

  • Open or short in rear height control sensor sub-assembly LH circuit

  • Rear height control sensor sub-assembly LH

  • Headlight light control ECU sub-assembly LH

  • Harness or connector

WIRING DIAGRAM

A01XOQUE13
*a Rear Height Control Sensor Sub-assembly LH
*b Headlight Light Control ECU Sub-assembly LH

CAUTION / NOTICE / HINT

Note


  • After the headlight light control ECU sub-assembly LH is replaced, vehicle information registration and initialization are necessary.

    Click here

  • After the rear hight control sensor sub-assembly LH is replaced or removed and installed, initialization is necessary.

    Click here

  • Before performing the check, check that the rear height control sensor sub-assembly LH is installed properly.

    Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Turn the engine switch on (IG).

    2. Inspect the light using the dimmer switch.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      Result
      Proceed to
      DTC B2416 and B241A output does not occur
      DTC B2416 or B241A output occurs

    DTC B2416 and B241A output does not occur

    USE SIMULATION METHOD TO CHECK Click here

    DTC B2416 or B241A output occurs

  3. CHECK HARNESS AND CONNECTOR (HEADLIGHT LIGHT CONTROL ECU ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)


    1. Disconnect the A19 headlight light control ECU sub-assembly LH connector.

    2. Disconnect the R1 rear height control sensor sub-assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A19-16 (SBR) - R1-3 (SHB) Always Below 1 Ω
      A19-17 (SHRL) - R1-2 (SHRR) Always Below 1 Ω
      A19-15 (SGR) - R1-1 (SHG) Always Below 1 Ω
      A19-16 (SBR) - Body ground Always 10 kΩ or higher
      A19-17 (SHRL) - Body ground Always 10 kΩ or higher
      A19-15 (SGR) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


    1. Remove the rear height control sensor sub-assembly LH.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTC


    1. Turn the engine switch on (IG).

    2. Inspect the light using the dimmer switch.

    3. Check for DTCs.

      Click here


      Body Electrical > HL AutoLeveling > Trouble Codes
      Result
      Proceed to
      DTC B2416 and B241A output does not occur
      DTC B2416 or B241A output occurs

    DTC B2416 and B241A output does not occur

    END (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH WAS DEFECTIVE)

    DTC B2416 or B241A output occurs

    REPLACE HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY LH Click here