PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU), Diagnostic DTC:C1611

DTC Code DTC Name
C1611 ECU Malfunction

DESCRIPTION

This DTC is stored if the television camera assembly judges that there is an internal malfunction as a result of its self check.

Tip:

The television camera assembly stores different types of information during initialization. If the television camera assembly cannot read the stored information when it is activated, the television camera assembly judges that there is an internal malfunction and stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1611

ECU Malfunction

  • EEPROM Status (Initial read)

  • ASIC Output Status

  • Parking assist monitor system initialization (not initialized television camera assembly)

  • Back camera setting (initialized television camera assembly)

  • Steering Angle setting (initialized television camera assembly)

  • Television camera assembly

CAUTION / NOTICE / HINT

Note:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click here

PROCEDURE

  1. READ VALUE USING GTS (TELEVISION CAMERA ASSEMBLY STATUS)

    1. Use the Data List to check if the television camera assembly status is functioning properly.

      Click here

      Chassis > IPA/Parking Assist Monitor > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      EEPROM Status (Initial read)

      Television camera assembly information

      OK or NG

      OK: Television camera assembly is normal

      NG: Television camera assembly is abnormal

      -

      ASIC Output Status

      Output condition of camera display signal

      OK or NG

      OK: Output condition of camera display signal is normal

      NG: Output condition of camera display signal is abnormal

      If "NG" is displayed, there is a malfunction in the television camera assembly.

      Chassis > IPA/Parking Assist Monitor > Data List

      Tester Display

      EEPROM Status (Initial read)

      ASIC Output Status

      Result

      Result

      Proceed to

      OK is displayed for both items.

      A

      NG is displayed for EEPROM Status (Initial read).

      NG is displayed for ASIC Output Status

      B
    B

    REPLACE TELEVISION CAMERA ASSEMBLY

    Click here

    A

  2. SETTINGS (TELEVISION CAMERA ASSEMBLY INITIALIZATION)

    Tip:

    • The television camera assembly stores different types of information during initialization. If the television camera assembly cannot read the stored information when it is activated, the television camera assembly judges that there is an internal malfunction and stores this DTC.

    • If the television camera assembly cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.

    1. Use the transition of diagnosis screens (note which transition pattern occurs) to confirm if the television camera assembly was able to properly store the information from initialization.

      Click here

      Tip:

      The procedure to make the television camera assembly store the vehicle information differs when the television camera assembly has stored the information (initialized) and when the information has not been stored (not initialized).

    2. Perform the following procedure depending on the memory conditions to register the vehicle information into the television camera assembly.

      Condition

      Procedure

      Not initialized

      Television camera assembly initialization

      Click here

      Initialized

      • Steering angle setting (Diagnosis system)

        Click here

      Result

      Result

      NEXT
    NEXT

  3. CHECK FOR DTC

    1. Clear the DTCs.

      Click here

      Chassis > IPA/Parking Assist Monitor > Clear DTCs

    2. Check for DTCs.

      Click here

      Chassis > IPA/Parking Assist Monitor > Trouble Codes

      Result

      Result

      Proceed to

      No DTC is output

      A

      DTC C1611 is output

      B
      Tip:

      • If DTC C1611 is output, perform the procedure to allow the television camera assembly to store the vehicle information again.

      • If DTC C1611 is still output after performing the procedure to make the television camera assembly store the vehicle information 3 times, replace the television camera assembly.

      • If DTC C1611 is output frequently, replace the television camera assembly even though the DTC is not output when rechecking for DTCs.

    A

    END (SETTINGS ARE DEFECTIVE)

    B

    REPLACE TELEVISION CAMERA ASSEMBLY

    Click here