FRONT SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE

  1. INSTALL SEAT TRACK ADJUSTING HANDLE

    1. B221235

      Attach the 2 springs to install the seat track adjusting handle to the front seat adjuster assembly LH.

  2. INSTALL FRONT NO. 2 SEAT CUSHION PROTECTOR

    B220267

    1. Attach the 6 hooks to install the front No. 2 seat cushion protector to the front seat cushion spring.

  3. INSTALL FRONT NO. 1 SEAT CUSHION PROTECTOR

    B220266

    1. Attach the 4 hooks to install the front No. 1 seat cushion protector to the front seat cushion spring.

  4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    1. B220321E01

      Install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH in the order shown in the illustration.

  5. INSTALL SEAT TRACK CONTROL CABLE CLAMP

    B222739

    1. Attach the claw to install the seat track control cable clamp.

  6. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH

    B295691

    1. Install the front seat adjuster assembly LH to the front seatback spring sub-assembly with the 4 bolts.

      42 N*m

      428 kgf*cm

      31 ft.*lbf

    2. B220318

      Attach the 5 wire harness clamps.

  7. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

    B168548

    1. Install the front seat lower cushion shield LH with the screw.

  8. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

    Tip:

    Use the same procedure described for the LH side.

  9. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH

    B168439

    1. Install the lower reclining adjuster inside cover LH with the screw.

  10. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER RH

    Tip:

    Use the same procedure described for the LH side.

  11. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

    B221230

    1. Attach the hook.

    2. Install the upper reclining adjuster inside cover LH with the screw.

  12. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

    Tip:

    Use the same procedure described for the LH side.

  13. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH

    Click here

  14. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    1. B222741

      Install the separate type front seatback pad.

    2. B222746E01

      Using hog ring pliers, connect the 2 straps to the separate type front seatback pad with new hog rings.

      Table 1. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      Be careful not to damage the cover.

    3. B275548E01

      w/o Table:

      Using hog ring pliers, install the upper part of the separate type front seatback cover to the seatback wire with new hog rings.

      Table 2. Text in Illustration

      *1

      Seatback Wire

      *2

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    4. B275583E03

      w/ Table:

      Using hog ring pliers, install the upper part of the separate type front seatback cover to the seatback wire with new hog rings.

      Table 3. Text in Illustration

      *1

      Seatback Wire

      *2

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    5. B220683

      Attach the 2 hooks.

    6. B220682

      Attach the 2 hooks.

    7. B275578E01

      Attach the seatback cover bracket and install the nut.

      Table 4. Text in Illustration

      *1

      Seatback Cover Bracket

      5.5 N*m

      56 kgf*cm

      49 in.*lbf

      Note:

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    8. B275580E01

      Using hog ring pliers, install the center of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Table 5. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    9. B275576E01

      Using hog ring pliers, attach the 2 straps to the separate type front seatback pad with new hog rings.

      Table 6. Text in Illustration

      *1

      Hog Ring Pliers
    10. B275543

      Attach the 2 hooks.

    11. B275542E03

      Using hog ring pliers, attach the 2 straps to the lower seatback frame with new hog rings.

      Table 7. Text in Illustration

      *1

      Hog Ring

      *2

      Hook

      *3

      Lower Seatback Frame

      *4

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    12. Attach the 2 hooks.

    13. B276104E01

      Using hog ring pliers, attach the 2 wires at the bottom of the separate type front seatback cover with new hog rings.

      Table 8. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  15. INSTALL FRONT SEATBACK TABLE ASSEMBLY LH (w/ Table)

    1. B222743

      Install the front seatback table assembly LH with the 4 screws.

  16. INSTALL FRONT SEAT HEADREST SUPPORT

    1. B222742

      Attach the 4 claws to install the 2 front seat headrest supports.

  17. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Click here

  18. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    1. B222751E01

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

      Table 9. Text in Illustration

      *1

      Hog Ring Pliers
      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  19. INSTALL SEAT CUSHION COVER WITH PAD

    B221968

    1. Set the seat cushion cover with pad in place.

    2. Attach the hooks to install the seat cushion cover with pad.

    3. B220680E04

      Attach the 3 hooks and wire harness clamp.

      Table 10. Text in Illustration

      *A

      w/ Seat Heater System

      *1

      Wire Harness Clamp

      *2

      Hook

    4. w/ Seat Heater System:

      1. Connect the connector.

      2. B220262

        Attach the 3 wire harness clamps.

    5. B275539

      for Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    6. B275569E01

      Attach the piece of fastening tape to connect the airbag wire harness.

      Table 11. Text in Illustration

      *1

      Fastening Tape

      *2

      Airbag Wire Harness

  20. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

    B187032

    1. Install the 2 front seat cushion edge protectors.

  21. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  22. INSTALL FRONT SEAT UNDER TRAY (w/ Under Tray)

    1. B222744

      Attach the 2 hooks to install the front seat under tray.

  23. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tip:

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.

    1. B275533

      Install the separate type front seatback assembly with the 4 bolts.

      42 N*m

      428 kgf*cm

      31 ft.*lbf

    2. for Driver Side:

      1. B296026

        w/ Seat Heater System:

        Connect the connector.

      2. B275538E02

        Connect the airbag wire harness.

        Note:

        Be careful not to damage the airbag wire harness or connector.

        Attach the piece of fastening tape to connect the airbag wire harness.

        Table 12. Text in Illustration

        *1

        Seat Track Control Cable Clamp

        *2

        Fastening Tape

      3. Attach the 2 wire harness clamps.

      4. Connect the airbag wire harness to the seat track control cable clamp and attach the claw to close the seat track control cable clamp.

      5. Attach the claw to connect the airbag connector.

    3. for Front Passenger Side:

      1. B296027

        w/ Seat Heater System:

        Connect the connector.

      2. B275536E02

        Connect the airbag wire harness.

        Note:

        Be careful not to damage the airbag wire harness or connector.

        Attach the piece of fastening tape to connect the airbag wire harness.

        Table 13. Text in Illustration

        *1

        Seat Track Control Cable Clamp

        *2

        Fastening Tape

      3. Attach the 2 wire harness clamps.

      4. Connect the airbag wire harness to the seat track control cable clamp and attach the claw to close the seat track control cable clamp.

      5. Attach the claw to connect the airbag connector.

    4. Install the outer reclining adjuster cover LH with the screw.

      B275534

    5. Install the outer reclining adjuster cover RH with the screw.

    6. Attach the 2 hooks.

      B275530

  24. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    1. B220252E01

      Attach the wire harness clamp.

      Table 14. Text in Illustration

      *1

      Wire Harness Clamp

      *2

      Hook

    2. Slide the front seat inner cushion shield LH to attach the hook.

    3. B220253

      Push the front seat inner cushion shield LH to attach the hook and claw.

    4. Install the front seat inner cushion shield with the screw.

  25. INSTALL FRONT SEAT CUSHION SHIELD LH

    1. B275892

      Slide the front seat cushion shield LH to attach the 2 hooks.

      Table 15. Text in Illustration
      V100136

      Slide
      V100135

      Push

    2. Push the front seat cushion shield LH to attach the claw.

    3. Install the front seat cushion shield LH with the 2 screws.

    4. B275532

      Attach the 2 hooks to connect the 2 rubber bands.

  26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

    1. B222766

      Attach the claw to install the reclining adjuster release handle LH.

  27. INSTALL VERTICAL ADJUSTING HANDLE LH

    B220257

    1. Install the vertical adjusting handle LH with the 2 screws.

  28. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP

    1. B276100

      Attach the 2 claws to install the vertical seat adjuster knob cap.

  29. INSTALL SEAT ADJUSTER COVER CAP LH

    1. B224148

      Install the 2 seat adjuster cover caps.