WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Key Unlock Warning SW

      Unlock warning switch

      ON or OFF

      ON: Ignition key inserted

      OFF: Ignition key not inserted

      -

      ACC SW

      Ignition switch ACC signal

      ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      "ON" is also displayed for this item when the ignition switch is ON

      IG SW

      Ignition switch ON signal

      ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      "OFF" is also displayed for this item when the ignition switch is ACC

      RR Door Courtesy SW

      Rear door courtesy light switch RH signal

      ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      -

      RL Door Courtesy SW

      Rear door courtesy light switch LH signal

      ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      -

      Back Door Courtesy SW

      Back door courtesy switch signal

      ON or OFF

      ON: Back door open

      OFF: Back door closed

      -

      Back Door Open

      Back door lock signal

      Permit or Prohibt

      Permit: Back door unlocked

      Prohibt: Back door locked

      -

      FR Door Lock Pos

      Front door RH unlock detection switch signal

      LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      -

      FR Door Courtesy SW

      Front door courtesy light switch RH signal

      ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      -

      FL Door Lock Pos

      Front door LH unlock detection switch signal

      LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      -

      FL Door Courtesy SW

      Front door courtesy light switch LH signal

      ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      -

      RR-Door Lock Pos SW

      Rear door RH and LH unlock detection switch signal

      ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      *1*2

      RL-Door Lock Pos SW

      Rear door RH and LH unlock detection switch signal

      ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      *1*3

      Wireless Control

      Wireless door lock control function

      ON or OFF

      Customization status displayed

      -

      Hazard Answer Back

      Hazard answer-back of wireless

      ON or OFF

      Customization status displayed

      *4

      Auto Lock Time

      Automatic lock time

      120 s, 60 s or 30 s

      Customization status displayed

      -

      • *1: w/ Theft Deterrent System

      • *2: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.

      • *3: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.

      • *4: for the vehicles displaying the Item "Hazard Answer Back" on the GTS

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Body Electrical > Main Body > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Door Lock

      Door lock motor

      OFF/Unlock/Lock

      -

      Trunk and Back-Door Open

      Back door lock motor

      OFF/ON

      -