FRONT DOOR REMOVAL

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE

  1. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

    1. B222052

      Using moulding remover A, detach the 3 claws and remove the inside handle bezel.

  4. REMOVE FRONT DOOR TRIM MOULDING LH

    1. B222053

      Using moulding remover A, detach the 8 claws and remove the front door trim moulding.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

    1. B222054E02

      Using moulding remover A, detach the clip and 7 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Tip:

    Use the same procedure described for the driver side.

  7. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

    Click here

  8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

    Click here

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    1. B222055

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. w/ Courtesy Light:

      1. Disconnect the courtesy light connector.

    4. B222057E02

      Pull out the front door trim board in the direction indicated by the arrow.

      Table 1. Text in Illustration

      *1

      Reference Boss
    5. B222058

      Disconnect the 2 cables from the inside handle.

  10. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  11. REMOVE FRONT DOOR LOWER TRIM COVER (w/o Courtesy Light)

    1. B222096

      Detach the 2 claws and remove the front door lower trim cover.

  12. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

    1. B222059

      Detach the 2 claws and remove the inside handle sub-assembly from the door trim board.

  13. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

    1. B222060

      Detach the 5 claws and remove the weatherstrip.

  14. REMOVE OUTER MIRROR INSTALL HOLE COVER LH

    1. B230239

      Using moulding remover D, detach the 3 claws and remove the outer mirror install hole cover.

  15. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    1. B222062

      Disconnect the 2 connectors and remove the service hole cover.

      Tip:

      Remove the remaining tape on the door.

  16. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  18. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    1. for Driver Side:

      Temporarily install the master switch assembly.

    2. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Move the door glass until the bolts appear in the service holes.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note:

      When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

    6. B222063

      Remove the 2 bolts.

      Note:

      Be careful when removing the bolts as the glass may fall and become damaged.

    7. B222064

      Remove the door glass in the direction indicated by the arrows in the illustration.

      Tip:

      Remove the glass upward.

      Note:

      Be careful not to damage the glass.

    8. for Driver Side:

      Remove the master switch assembly.

    9. for Front Passenger Side:

      Remove the regulator switch assembly.

  19. REMOVE FRONT DOOR GLASS RUN LH

    1. B222065

      Remove the front door glass run.

  20. REMOVE DOOR FRAME GARNISH LH

    1. B222056

      Detach the clip and remove the door frame garnish.

  21. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

    Click here

  22. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    1. Disconnect the connector from the front door window regulator assembly.

    2. B222066E02

      Loosen the temporary bolt.

      Table 2. Text in Illustration

      *1

      Temporary Bolt
      Note:

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator assembly.

    5. Remove the temporary bolt from the front door window regulator assembly.

  23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

    1. B222067

      Remove the bolt and rear lower frame.

  24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

    1. B222068

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock key cylinder installed.

    3. B222069

      Using a screwdriver, disengage the 3 claws and remove the front door outside handle cover from the cylinder.

  25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

    1. B222070

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover.

  26. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

    1. w/ Entry and Start System:

      1. B213414E09

        Disconnect the 2 claws of the connector cover as shown in the illustration.

        Table 3. Text in Illustration

        *1

        Screwdriver

        *2

        Connector Cover

        *3

        Front Door Outside Handle Assembly

        *4

        Front Door Wire LH
      2. B213415E04

        Push the claw of the connector and disconnect the front door wire as shown in the illustration.

        Table 4. Text in Illustration

        *1

        Screwdriver

        *2

        Front Door Wire LH
      3. B213416E03

        Detach the holder as shown in the illustration.

        Table 5. Text in Illustration

        *1

        Holder
      4. B222071

        Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

    2. w/o Entry and Start System:

      1. U122434E03

        Detach the holder as shown in the illustration.

        Table 6. Text in Illustration

        *1

        Holder
      2. B222072

        Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  27. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

    1. B222073

      Detach the 3 claws and remove the pad.

  28. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

    1. B222074

      Detach the 2 claws and remove the pad.

  29. REMOVE FRONT DOOR LOCK ASSEMBLY LH

    Click here

  30. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

    1. B222075

      Remove the front door lock remote control cable assembly.

  31. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

    1. B222076

      Using a screwdriver, detach the 3 claws.

      Tip:

      Tape the screwdriver tip before use.

    2. B222077

      Remove the front door inside locking cable assembly.

  32. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

    1. w/ Entry and Start System:

      1. B222078

        Detach the 3 clamps.

      2. B222079

        Using a T30 "TORX" wrench, loosen the screw.

      3. Slide the outside handle frame and door wire to remove the outside handle frame.

        Tip:

        Remove the outside handle frame through the service hole.

      4. Pull the front door outside handle frame sub-assembly together with the front door wire away from the vehicle.

      5. B213422

        Detach the 2 clamps and 2 claws and remove the front door outside handle frame from the front door wire.

    2. w/o Entry and Start System:

      1. B222080

        Using a T30 "TORX" wrench, loosen the screw.

      2. Slide the outside handle frame to remove it.

        Tip:

        Remove the outside handle frame through the service hole.

  33. REMOVE FRONT DOOR LOCK OPEN ROD LH

    1. B455642E01

      Remove the front door lock open rod as shown in the illustration.

  34. REMOVE FRONT DOOR CHECK ASSEMBLY LH

    B222081

    1. Remove the bolt, 2 nuts and door check.

      Tip:

      Remove the door check through the service hole.

      Note:

      Be careful when removing the bolt and nuts as the door check may fall and become damaged.

  35. REMOVE FRONT DOOR WEATHERSTRIP LH

    1. B222082E02

      Using a clip remover, remove the clip labeled A.

    2. Using a clip remover, detach the 14 clips and remove the weatherstrip.

      Tip:

      If clips are damaged during removal, replace them.

  36. REMOVE NO. 1 BLACK OUT TAPE LH

    Click here

  37. REMOVE NO. 2 BLACK OUT TAPE LH

    Click here