CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P1586

DTC Code DTC Name
P1586 Acceleration Sensor Malfunction

DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the airbag sensor assembly (yaw rate and acceleration sensor). If a malfunction is determined in the airbag sensor assembly (yaw rate and acceleration sensor) based on a malfunction signal from the brake actuator assembly, the ECM cancels neutral control as a fail-safe function.

Tip:

  • The signal of the airbag sensor assembly (yaw rate and acceleration sensor) is sent to the brake actuator assembly via the CAN communication system.

  • If CAN communication DTCs are output, perform troubleshooting for those DTCs first.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P1586

Acceleration Sensor Malfunction

  1. Diagnosis Condition

    • The ignition switch is ON.

  3. Malfunction Status

    • At a vehicle speed 30 km/h (18 mph) or more, the difference between longitudinal G calculated based on the G sensor value and longitudinal G calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.

  5. Malfunction Time

    • 3 seconds or more

  7. Other

    • 1-trip detection logic

  1. Diagnosis Condition

    • The ignition switch is ON.

  3. Malfunction Status

    • The airbag sensor assembly (yaw rate and acceleration sensor) signal does not change 16 times or more while the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h.

  5. Malfunction Time

    • 3 seconds or more

  7. Other

    • 1-trip detection logic

  • Airbag sensor assembly (Yaw rate and acceleration sensor)

  • Brake actuator assembly (Skid control ECU)

  • CAN communication system

Does not come on

DTC stored

WIRING DIAGRAM

Refer to DTC P1585

Click here

PROCEDURE

  1. CHECK DTC OUTPUT

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Check for DTCs.

      Click here

      Powertrain > Engine and ECT > Trouble Codes

    Result

    Result

    Proceed to

    DTC U0129 is not output

    A

    DTC U0129 is output

    B
    B

    GO TO CAN COMMUNICATION SYSTEM

    w/o Central Gateway ECU:Click hereClick hereClick here

    w/ Central Gateway ECU:Click hereClick here

    A

  2. CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

    1. Connect the GTS to the DLC3.

    2. Turn the GTS on.

    3. Turn the ignition switch to ON.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    5. Perform a road test where the vehicle is driven at 30 km/h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    7. Read the DTCs using the GTS.

      Tip:

      If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.

    Result

    Result

    Proceed to

    Only DTC P1586 is output

    A

    DTC P1586 and other DTCs are output

    B
    B

    GO TO DTC CHART

    Click here

    A

  3. READ VALUE USING GTS (G SENSOR)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.

    5. In accordance with the display on the GTS, read the Data List.

      Powertrain > Engine and ECT > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      G Sensor

      Converted output voltage of yaw rate and acceleration sensor

      min.: 0 V

      max.: 5 V

      Displays converted voltage of yaw rate and acceleration sensor

      • 2.31 V to 2.69 V: Vehicle on level ground

      • 1.88 V to 2.5 V: Decelerating

      • 2.5 V to 3.11 V: Accelerating

      • Set to 1.87 V: G sensor malfunction

      • Set to 1.87 V: Communication malfunction

      -

    Result

    Result

    Proceed to

    Data display is not within Normal Condition range

    A

    Data display is within Normal Condition range

    B
    B

    REPLACE BRAKE ACTUATOR ASSEMBLY

    Click hereClick here

    A

  4. REPLACE AIR BAG SENSOR ASSEMBLY (YAW RATE SENSOR)

    1. Replace the airbag sensor assembly (yaw rate sensor).

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    PERFORM INITIALIZATION

    Click here