AIRBAG SYSTEM, Diagnostic DTC:B1692/81 and B1697/82

DTC Code DTC Name
B1692/81 Lost Communication with Door Side Airbag Sensor RH
B1697/82 Lost Communication with Door Side Airbag Sensor LH

DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, rear airbag sensor LH or RH and side airbag sensor LH or RH.

The rear airbag sensor LH or RH and side airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1692/81 or B1697/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag LH or RH and curtain shield airbag LH or RH).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Test Mode / Check Mode

B1692/81

Lost Communication with Door Side Airbag Sensor RH

One of the following conditions is met:

  • The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat airbag RH and curtain shield airbag RH) for 2 seconds.

  • A side airbag sensor RH malfunction.

  • A rear airbag sensor RH malfunction.

  • A center airbag sensor malfunction.

  • Floor wire

  • Front door wire RH

  • Side airbag sensor RH

  • Rear airbag sensor RH

  • Center airbag sensor assembly

*1

B1697/82

Lost Communication with Door Side Airbag Sensor LH

One of the following conditions is met:

  • The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat airbag LH and curtain shield airbag LH) for 2 seconds.

  • A side airbag sensor LH malfunction.

  • A rear airbag sensor LH malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Front door wire LH

  • Side airbag sensor LH

  • Rear airbag sensor LH

  • Center airbag sensor assembly

*1

WIRING DIAGRAM

C175145E13
C175145E14

CAUTION / NOTICE / HINT

Note:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

PROCEDURE

  1. CHECK FOR DTC

    1. Turn the engine switch on (IG).

    2. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      Result

      Result

      Proceed to

      DTC B1692 and B1697 are not output

      A

      DTC B1697 is output

      B

      DTC B1692 is output

      C
      Tip:

      Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.

    B

    CHECK CONNECTION OF CONNECTORSClick here

    A

    USE SIMULATION METHOD TO CHECK

    Click here

    C

  2. CHECK CONNECTION OF CONNECTORS

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.

      OK

      The connectors are properly connected.

      Result

      Result

      OK

      NG
    NG

    CONNECT CONNECTORS PROPERLY

    OK

  3. CHECK CONNECTORS

    1. C213961C03

      *1

      Rear Airbag Sensor RH

      *2

      Side Airbag Sensor RH

      *3

      Center Airbag Sensor

      Disconnect the connectors from the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.

    2. Check that the connectors (on the center airbag sensor side, rear airbag sensor RH side and side airbag sensor RH side) are not damaged.

      OK

      The connectors are not deformed or damaged.

      Result

      Result

      OK

      NG
    NG

    REPLACE HARNESS AND CONNECTOR

    OK

  4. CHECK REAR AIRBAG SENSOR RH

    1. C171812C13

      *1

      Rear Airbag Sensor LH

      *2

      Center Airbag Sensor

      Connect the connectors to the center airbag sensor and side airbag sensor RH.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      Result

      Result

      Proceed to

      DTC B1692 and B1697 are not output

      A

      DTC B1697 is output

      B

      DTC B1692 is output

      C
      Tip:

      Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.

    A

    USE SIMULATION METHOD TO CHECK

    Click here

    B

    REPLACE REAR AIRBAG SENSOR RH

    Click here

    C

  5. CHECK SIDE AIRBAG SENSOR RH CIRCUIT

    1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

      C213922C06

      *1

      Side Airbag Sensor RH

      *2

      Rear Airbag Sensor RH

      *3

      Connector E

      *4

      Connector B

      *5

      Service Wire

      -

      -

      *a

      Rear view of wire harness connector

      (to Side Airbag Sensor RH)

      *b

      Rear view of wire harness connector

      (to Rear Airbag Sensor RH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      Q4-1 (BCR+) - Body ground

      Engine switch on (IG)

      Below 1 V

      Q4-2 (BCR-) - Body ground

      Engine switch on (IG)

      Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q4-1 (BCR+) - Q4-2 (BCR-)

      Always

      Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q4-1 (BCR+) - Q4-2 (BCR-)

      Always

      1 MΩ or higher

      Q4-1 (BCR+) - Body ground

      Always

      1 MΩ or higher

      Q4-2 (BCR-) - Body ground

      Always

      1 MΩ or higher

      Result

      Result

      OK

      NG
    NG

    CHECK FLOOR WIRE (REAR AIRBAG SENSOR RH - FRONT DOOR WIRE RH)Click here

    OK

  6. CHECK SIDE AIRBAG SENSOR RH

    1. C171828C12

      *1

      Side Airbag Sensor LH

      *2

      Rear Airbag Sensor RH

      Connect the connector to the rear airbag sensor RH.

    2. Interchange the side airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      Result

      Result

      Proceed to

      DTC B1692 and B1697 are not output

      A

      DTC B1697 is output

      B

      DTC B1692 is output

      C
      Tip:

      Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.

    A

    USE SIMULATION METHOD TO CHECK

    Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

    Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY

    Click here

  7. CHECK FLOOR WIRE (REAR AIRBAG SENSOR RH - FRONT DOOR WIRE RH)

    1. Disconnect the floor wire connector from the front door wire RH.

      C217387C03

      *1

      Side Airbag Sensor RH

      *2

      Rear Airbag Sensor RH

      *3

      Front Door Wire RH

      *4

      Floor Wire

      *5

      Connector C

      *6

      Connector B

      *7

      Service Wire

      -

      -

      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      *b

      Rear view of wire harness connector

      (to Rear Airbag Sensor RH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      Q4-1 (BCR+) - Body ground

      Engine switch on (IG)

      Below 1 V

      Q4-2 (BCR-) - Body ground

      Engine switch on (IG)

      Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector C.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q4-1 (BCR+) - Q4-2 (BCR-)

      Always

      Below 1 Ω

    8. Disconnect the service wire from connector C.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      Q4-1 (BCR+) - Q4-2 (BCR-)

      Always

      1 MΩ or higher

      Q4-1 (BCR+) - Body ground

      Always

      1 MΩ or higher

      Q4-2 (BCR-) - Body ground

      Always

      1 MΩ or higher

      Result

      Result

      OK

      NG
    OK

    REPLACE FRONT DOOR WIRE RH

    NG

    REPLACE FLOOR WIRE

  8. CHECK CONNECTION OF CONNECTORS

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.

      OK

      The connectors are properly connected.

      Result

      Result

      OK

      NG
    NG

    CONNECT CONNECTORS PROPERLY

    OK

  9. CHECK CONNECTORS

    1. C214698C03

      *1

      Rear Airbag Sensor LH

      *2

      Side Airbag Sensor LH

      *3

      Center Airbag Sensor

      Disconnect the connectors from the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.

    2. Check that the connectors (on the center airbag sensor side, rear airbag sensor LH side and side airbag sensor LH side) are not damaged.

      OK

      The connectors are not deformed or damaged.

      Result

      Result

      OK

      NG
    NG

    REPLACE HARNESS AND CONNECTOR

    OK

  10. CHECK AIR BAG SENSOR REAR LH

    1. C146229C09

      *1

      Rear Airbag Sensor RH

      *2

      Center Airbag Sensor

      Connect the connector to the center airbag sensor and side airbag sensor LH.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      Result

      Result

      Proceed to

      DTC B1692 and B1697 are not output

      A

      DTC B1692 is output

      B

      DTC B1697 is output

      C
      Tip:

      Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.

    A

    USE SIMULATION METHOD TO CHECK

    Click here

    B

    REPLACE REAR AIRBAG SENSOR LH

    Click here

    C

  11. CHECK SIDE AIRBAG SENSOR LH CIRCUIT

    1. Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.

      C213922C07

      *1

      Side Airbag Sensor LH

      *2

      Rear Airbag Sensor LH

      *3

      Connector E

      *4

      Connector B

      *5

      Service Wire

      -

      -

      *a

      Rear view of wire harness connector

      (to Side Airbag Sensor LH)

      *b

      Rear view of wire harness connector

      (to Rear Airbag Sensor LH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      R6-1 (BCL+) - Body

      Engine switch on (IG)

      Below 1 V

      R6-2 (BCL-) - Body ground

      Engine switch on (IG)

      Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      R6-1 (BCL+) - R6-2 (BCL-)

      Always

      Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      R6-1 (BCL+) - R6-2 (BCL-)

      Always

      1 MΩ or higher

      R6-1 (BCL+) - Body ground

      Always

      1 MΩ or higher

      R6-2 (BCL-) - Body ground

      Always

      1 MΩ or higher

      Result

      Result

      OK

      NG
    NG

    CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)Click here

    OK

  12. CHECK SIDE AIRBAG SENSOR LH

    1. C171828C13

      *1

      Side Airbag Sensor RH

      *2

      Rear Airbag Sensor LH

      Connect the connector to the rear airbag sensor LH.

    2. Interchange the side airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here

      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs.

      Click here

      Body Electrical > SRS Airbag > Trouble Codes

      Result

      Result

      Proceed to

      DTC B1692 and B1697 are not output

      A

      DTC B1692 is output

      B

      DTC B1697 is output

      C
      Tip:

      Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.

    9. Turn the engine switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.

    A

    USE SIMULATION METHOD TO CHECK

    Click here

    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

    Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY

    Click here

  13. CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)

    1. Disconnect the No. 2 floor wire connector from the front door wire LH.

      C217387C04

      *1

      Side Airbag Sensor LH

      *2

      Rear Airbag Sensor LH

      *3

      Front Door Wire LH

      *4

      No. 2 Floor Wire

      *5

      Connector C

      *6

      Connector B

      *7

      Service Wire

      -

      -

      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      *b

      Rear view of wire harness connector

      (to Rear Airbag Sensor LH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      R6-1 (BCL+) - Body ground

      Engine switch on (IG)

      Below 1 V

      R6-2 (BCL-) - Body ground

      Engine switch on (IG)

      Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      R6-1 (BCL+) - R6-2 (BCL-)

      Always

      Below 1 Ω

    8. Disconnect the service wire from connector C.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      R6-1 (BCL+) - R6-2 (BCL-)

      Always

      1 MΩ or higher

      R6-1 (BCL+) - Body ground

      Always

      1 MΩ or higher

      R6-2 (BCL-) - Body ground

      Always

      1 MΩ or higher

      Result

      Result

      OK

      NG
    OK

    REPLACE FRONT DOOR WIRE LH

    NG

    REPLACE NO. 2 FLOOR WIRE