FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) Power Seat Power Easy Access System Function does not Operate

DESCRIPTION


WIRING DIAGRAM

B005M0SE27

CAUTION / NOTICE / HINT

Note


  • The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

  • The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before proceeding with troubleshooting, perform an on-vehicle inspection and confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

    Click here


    • *: w/o Canister Pump Module with Door Ajar Warning Buzzer Function

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK FRONT POWER SEAT OPERATION


    1. Check that each function of the power seat operates normally by using the position control ECU and switch assembly (driver seat).

      Click here

      Result
      Result Proceed to
      Power seat functions operate normally A
      All power seat functions do not operate B
      One or more power seat motors do not operate C

    B

    GO TO OTHER DIAGNOSTIC PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch) Click here

    C

    GO TO OTHER DIAGNOSTIC PROCEDURE (One or more Power Seat Motors do not Operate) Click here

    A

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Driver Seat / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Driver Seat > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Driver Seat Buckle SW Driver seat belt buckle switch ON or OFF

      ON: Driver seat belt fastened

      OFF: Driver seat belt unfastened

      		 -

      Body Electrical > Driver Seat > Data List
      Tester Display
      Driver Seat Buckle SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SEAT) - IG POWER SUPPLY)


    1. Disconnect the S2*1 or R6*2 front seat outer belt assembly (driver seat) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      S2-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      S2-1 (IG) - Body ground Engine switch off Below 1 V
      for RHD
      Tester Connection Condition Specified Condition
      R6-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      R6-1 (IG) - Body ground Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SEAT) - POSITION CONTROL ECU AND SWITCH ASSEMBLY (DRIVER SEAT))


    1. Disconnect the c6*1 or b17*2 position control ECU and switch assembly (driver seat) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      S2-2 (L) - c6-9 (RDC) Always Below 1 Ω
      S2-2 (L) or c6-9 (RDC) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      R6-2 (L) - b17-9 (DRDC) Always Below 1 Ω
      R6-2 (L) or b17-9 (DRDC) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK SEAT BELT TENSION REDUCER SYSTEM


    1. Check the seat belt tension reducer system.

      Click here

      OK
      Seat belt tension reducer system is normal.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SEAT) Click here

    OK

  6. REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (DRIVER SEAT)


    1. Replace the position control ECU and switch assembly (driver seat) with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK POWER SEAT POWER EASY ACCESS SYSTEM


    1. Check the power seat power easy access system.

      Click here

      OK
      Power seat power easy access system is normal.
      Result
      Proceed to
      OK
      NG

    OK

    END (POSITION CONTROL ECU AND SWITCH ASSEMBLY (DRIVER SEAT) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  8. INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)


    1. Remove the front seat inner belt assembly (driver seat).

      Click here

    2. Inspect the front seat inner belt assembly (driver seat).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY (DRIVER SEAT) - FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT))


    1. Disconnect the c6*1 or b17*2 position control ECU and switch assembly (driver seat) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      c6-10 (DBCL) - c11-1 (RDC) Always Below 1 Ω
      c6-10 (DBCL) or c11-1 (RDC) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      b17-10 (DBCL) - b8-1 (RDC) Always Below 1 Ω
      b17-10 (DBCL) or b8-1 (RDC) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (DRIVER SEAT) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR