AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P0748

DTC Code DTC Name
P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0748

Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

An open or short circuit (output signal duty is 0% or 100%) is detected by the TCM in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gears (SL1 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).

  • Open or short in shift solenoid valve SL1 circuit

  • Shift solenoid valve SL1

  • TCM

Comes on

DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the TCM stops sending current to the circuit.)

While driving and shifting between 4th and 5th gears, if the TCM detects an open or short in the shift solenoid valve SL1 circuit, the TCM determines there is a malfunction.

Click here

WIRING DIAGRAM

C279421E01

CAUTION / NOTICE / HINT

Note:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tip:

The following table shows normal operation of shift solenoid valve SL1 when the shift lever is in D:

TCM gear shift command

1st

2nd

3rd

4th

5th

6th

Shift solenoid valve SL1

ON

ON

ON

ON

OFF

OFF

PROCEDURE

  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)

    1. Remove the TCM.

    2. C207057C15

      *a

      Component without TCM connected

      (Transmission Wire)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      14 (SL1+) - 13 (SL1-)

      20°C (68°F)

      5.0 to 5.6 Ω

      14 (SL1+) - Body ground

      Always

      10 kΩ or higher

      13 (SL1-) - Body ground

      Always

      10 kΩ or higher

      14 (SL1+) - All other terminals except 13 (SL1-)

      Always

      10 kΩ or higher

      13 (SL1-) - All other terminals except 14 (SL1+)

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE TCM

    Click here

    NG

  2. INSPECT SHIFT SOLENOID VALVE SL1

    1. C197715C16

      *1

      Shift Solenoid Valve SL1

      Remove shift solenoid valve SL1.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      20°C (68°F)

      5.0 to 5.6 Ω

    3. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK

      Measurement Condition

      Specified Condition

      • Battery positive (+) with a 21 W bulb → Terminal 1

      • Battery negative (-) → Terminal 2

      Valve moves and makes an operating noise

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE TRANSMISSION WIRE

    Click here

    NG

    REPLACE SHIFT SOLENOID VALVE SL1

    Click here