OUTER REAR VIEW MIRROR REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL OUTER MIRROR RETRACTOR (w/ Power Retract Mirror)


    1. B00897CE01

      Install the 2 screws in the order shown in the illustration.

    2. B0087M0

      Install a new frame sub-assembly to the housing with the 2 screws.

    3. B0085KPC01
      B00847Z Install in this Direction

      Pass a new wire harness sub-assembly through the frame sub-assembly as shown in the illustration.

    4. B00870P

      Connect the connector.

    5. B00867X

      Engage the 2 clamps.

    6. Connect the connector.

    7. B008722

      Install the actuator sub-assembly with the 3 screws.

    8. B0087FJ

      Wind vinyl tape around the wire harness sub-assembly to secure it.

    9. Pass the wire harness sub-assembly through the base sub-assembly.

    10. Remove the vinyl tape.

    11. B0083JB

      Using a T25 "TORX" socket wrench, install the base sub-assembly with 3 new screws.

      Note

      When installing the base sub-assembly, check that the wire harness sub-assembly is not caught between the base sub-assembly and body. Failure to do so may cause a short circuit.

    12. B008980

      Engage the guide and 8 claws to install a new lower cover.

    13. B0086MY

      Pass the wire harness sub-assembly through a new gasket sub-assembly and engage the 8 guides to install the gasket sub-assembly.

      Note

      Make sure there is no clearance between the gasket sub-assembly and base sub-assembly.

    14. B0085Y1C01
      *a Marking
      B00847Z Install in this Direction

      Adjust the wire harness sub-assembly so that the marking is at the position shown in the illustration.

    15. B00861OC02

      Wind vinyl tape around the wire harness sub-assembly to secure it.

      Reference Measurement
      Area Measurement
      A 40 mm (1.57 in.)
    16. B0084B5C02
      *a Clamp
      *b Guide

      Engage the guide.

    17. Install the bracket with the screw.

    18. Engage the clamp.

    19. B00897G

      Connect each connector to a new adapter.

    20. B00881OC01
      *a Wire Harness Routing

      Route the longer part of the wire harness sub-assembly as shown in the illustration.

    21. B0085YUC04
      *a Vinyl Tape

      Wind vinyl tape around the wire harness sub-assembly to secure it.

      Reference Measurement
      Area Measurement
      A 0 to 5.0 mm (0 to 0.1969 in.)
      B 50 mm (1.97 in.)
    22. B0083YYC02
      *a Vinyl Tape

      Wind vinyl tape around the clamp to secure it.

      Reference Measurement
      Area Measurement
      A 185 mm (7.28 in.)

  2. INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY

    Click here

  3. INSTALL NO. 2 OUTER MIRROR COVER


    1. B0084Z9C01
      B00847Z Install in this Direction

      Engage the 2 guides and 2 claws to install the No. 2 outer mirror cover as shown in the illustration.

  4. INSTALL OUTER MIRROR HOLE COVER ASSEMBLY (w/o Panoramic View Monitor System)

    Click here

  5. INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

    Click here

  6. INSTALL OUTER MIRROR HOLE COVER WITH SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)

    Click here

  7. INSTALL OUTER MIRROR COVER

    Click here

  8. INSTALL OUTER MIRROR

    Click here