STOP AND START SYSTEM, Diagnostic DTC:P1589

DTC Code DTC Name
P1589 G Sensor Zero Point Calibration Incomplete

DESCRIPTION

In case of driving the vehicle before performing calibration of the deceleration sensor zero point, the engine stop and start ECU stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Memory

P1589

G Sensor Zero Point Calibration Incomplete

The following conditions continue for 5 seconds or more (1 trip detection logic):

  • The vehicle speed is 3 km/h (2 mph) or more and ABS communication is normal.

  • Deceleration sensor zero point calibration is incomplete

  • The deceleration sensor zero point calibration has not been performed.

  • Airbag sensor assembly (Yaw rate sensor)

  • Skid control ECU (Brake actuator assembly)

  • Engine stop and start ECU

Blinking

DTC stored

CONFIRMATION DRIVING PATTERN

Tip:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here

  1. Tip:

    • When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

    • Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here

      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and warm it up.

    5. Drive the vehicle at 3 km/h (1.9 mph) or more for 5 seconds or more.

    6. Check that DTCs are not output.

      Click here

      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tip:

    When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to stop by stop and start control.

    6. Depress the clutch pedal and start the engine.

CAUTION / NOTICE / HINT

Note:

  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

    Click here

Tip:

  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here

PROCEDURE

  1. PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)

    Note:

    • Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.

    • Park the vehicle on a level surface (grade: +/-1 %). Do not shake the vehicle body or open/close any of the doors during zero point calibration. To avoid vibrations caused by the engine idling, do not start the engine.

    1. Clear the zero point calibration data.

      1. Turn the ignition switch off.

      2. Connect the GTS to the DLC3.

      3. Move the shift lever to neutral and apply the parking brake.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Clear
        Note:

        When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU stores DTC P1589 and blinks the stop and start cancel indicator light.

      7. Turn the ignition switch off.

    2. Perform zero point calibration of the deceleration sensor.

      1. Check the shift lever in neutral.

      2. Connect the GTS to the DLC3.

      3. Check that the parking brake is applied and the brake warning light is illuminated.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Calibration
        Tip:

        If DTC P1589 is stored, the stop and start cancel indicator light blinks.

      7. While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

        Note:

        If zero point calibration fails, perform again from "CLEAR THE ZERO POINT CALIBRATION DATA".

    Result

    Result

    Proceed to

    NG

    A

    OK

    B
    B

    END

    A

  2. READ VALUE USING GTS (GRADIENT OF ROAD SURFACE)

    1. Enter the following menus: Powertrain / Stop and Start / Data List / Gradient of Road Surface.

    2. Check the road gradient displayed on the GTS.

      Powertrain > Stop and Start > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Gradient of Road Surface

      Degree of road gradient

      0 to 20.4 m/s2

      • -0.7 - 0.7 m/s2 (Vehicle is stopped on level surface)

      • -0.7 m/s2 or less / 0.7m/s2 or more (Vehicle is stopped on slope road)

      Powertrain > Stop and Start > Data List

      Tester Display

      Gradient of Road Surface

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE AIRBAG SENSOR ASSEMBLYClick here

    OK

  3. CHECK AND REPLACE ENGINE STOP AND START ECU

    1. Check and replace the engine stop and start ECU.

      Click hereClick here

    Result

    Proceed to

    NEXT
    NEXT

  4. PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)

    Note:

    • Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.

    • Park the vehicle on a level surface (grade: +/-1 %). Do not shake the vehicle body or open/close any of the doors during zero point calibration. To avoid vibrations caused by the engine idling, do not start the engine.

    1. Clear the zero point calibration data.

      1. Turn the ignition switch off.

      2. Connect the GTS to the DLC3.

      3. Move the shift lever to neutral and apply the parking brake.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Clear
        Note:

        When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU stores DTC P1589 and blinks the stop and start cancel indicator light.

      7. Turn the ignition switch off.

    2. Perform zero point calibration of the deceleration sensor.

      1. Check the shift lever in neutral.

      2. Connect the GTS to the DLC3.

      3. Check that the parking brake is applied and the brake warning light is illuminated.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Calibration
        Tip:

        If DTC P1589 is stored, the stop and start cancel indicator light blinks.

      7. While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

        Note:

        If zero point calibration fails, perform again from "CLEAR THE ZERO POINT CALIBRATION DATA".

    Result

    Proceed to

    NEXT
    NEXT

    END

  5. REPLACE AIRBAG SENSOR ASSEMBLY

    1. Replace the airbag sensor assembly.

      Click hereClick here

    Result

    Proceed to

    NEXT
    NEXT

  6. PERFORM REGISTRATION (DECELERATION SENSOR ZERO POINT CLEAR, DECELERATION SENSOR ZERO POINT CALIBRATION)

    Note:

    • Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.

    • Park the vehicle on a level surface (grade: +/-1 %). Do not shake the vehicle body or open/close any of the doors during zero point calibration. To avoid vibrations caused by the engine idling, do not start the engine.

    1. Clear the zero point calibration data.

      1. Turn the ignition switch off.

      2. Connect the GTS to the DLC3.

      3. Move the shift lever to neutral and apply the parking brake.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Clear
        Note:

        When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU stores DTC P1589 and blinks the stop and start cancel indicator light.

      7. Turn the ignition switch off.

    2. Perform zero point calibration of the deceleration sensor.

      1. Check the shift lever in neutral.

      2. Connect the GTS to the DLC3.

      3. Check that the parking brake is applied and the brake warning light is illuminated.

      4. Turn the ignition switch to ON.

        Tip:

        Do not start the engine.

      5. Turn the GTS on.

      6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

        Powertrain > Stop and Start > Utility

        Tester Display

        Deceleration Sensor Zero Point Calibration
        Tip:

        If DTC P1589 is stored, the stop and start cancel indicator light blinks.

      7. While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

        Note:

        If zero point calibration fails, perform again from "CLEAR THE ZERO POINT CALIBRATION DATA".

    Result

    Result

    Proceed to

    OK

    A

    NG

    B
    A

    END

    B

    REPLACE ENGINE STOP AND START ECU

    Click hereClick here