LANE DEPARTURE ALERT SYSTEM(w/ Steering Control), Diagnostic DTC:C1AA1

DTC Code DTC Name
C1AA1 FCM Destination Information Unmatched

DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store country specification information received from the main body ECU (multiplex network body ECU). If the country specification information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU), DTC C1AA1 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA1 FCM Destination Information Unmatched 2 seconds after the power switch is turned on (IG), destination information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) do not match for 5 seconds or more.
  • CAN communication system

  • Forward recognition camera

  • Main body ECU (Multiplex network body ECU)

CAUTION / NOTICE / HINT

Note


  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

    Click here

Tech Tips

This DTC is stored when the destination information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.

PROCEDURE


  1. CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))

    Tech Tips

    When DTC C1AA1 is stored, DTC C1AAC may be stored at the same time.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1AAC is not output A
      DTC C1AAC is output B

    B
    A
  2. CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

    Tech Tips

    The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC U0142 is not output A
      DTC U0142 is output B

    B
    A
  3. CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 7 seconds or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1AA1 is not output A
      DTC C1AA1 is output B

    A
    B
  4. REPLACE FORWARD RECOGNITION CAMERA


    1. Replace the forward recognition camera.

      Click here

    2. Perform forward recognition camera adjustment.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  5. CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM (w/ Steering Control))


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

    5. Clear the DTCs.

      Click here

    6. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 7 seconds or more.

    7. Check for DTCs.

      Click here

      Result
      Result Proceed to
      DTC C1AA1 is not output A
      DTC C1AA1 is output B

    A
    B