AUDIO AND VISUAL SYSTEM(for 8 Inch Display), Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit

for Separate Type Amplifier:


  • Harness or connector

  • Speakers

  • Stereo component amplifier assembly

  • DCM (telematics transceiver) (w/ Telematics Transceiver)

for Built-in Type Amplifier:


  • Harness or connector

  • Speakers

  • Radio receiver assembly

  • DCM (telematics transceiver) (w/ Telematics Transceiver)

WIRING DIAGRAM

B008JOCE02
B008JN2E01

CAUTION / NOTICE / HINT

Note

When replacing the DCM (telematics transceiver), make sure to replace it with a new one (w/ Telematics Transceiver).

Tech Tips

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    2. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      for Separate Type Amplifier A
      for Built-in Type Amplifier B

    B

    CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for LH Side

      *2: for RH Side

      *3: w/ Telematics Transceiver


    1. Disconnect the P32 stereo component amplifier assembly connector.

    2. Disconnect the M9*1 and/or L9*2 front No. 1 speaker assembly connector.

    3. Disconnect the J9*1 and/or J8*2 front No. 2 speaker assembly connector.

    4. Disconnect the O6*1 and/or N5*2 rear No. 2 speaker assembly connector.

    5. Disconnect the O5*1 and/or N6*2 rear speaker assembly connector.

    6. Disconnect the I40 DCM (telematics transceiver) connector.*3

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH Side:
      Tester Connection Condition Specified Condition
      P32-4 (WFL+) - M9-1 Always Below 1 Ω
      P32-19 (WFL-) - M9-2 Always Below 1 Ω
      P32-12 (FL+) - J9-4 Always Below 1 Ω
      P32-27 (FL-) - J9-2 Always Below 1 Ω
      P32-8 (RL+) - O6-3 (+TW) Always Below 1 Ω
      P32-23 (RL-) - O6-1 (-TW) Always Below 1 Ω
      O6-4 (+) - O5-1 Always Below 1 Ω
      O6-2 (-) - O5-2 Always Below 1 Ω
      P32-4 (WFL+) - Body ground Always 10 kΩ or higher
      P32-19 (WFL-) - Body ground Always 10 kΩ or higher
      P32-12 (FL+) - Body ground Always 10 kΩ or higher
      P32-27 (FL-) - Body ground Always 10 kΩ or higher
      P32-8 (RL+) - Body ground Always 10 kΩ or higher
      P32-23 (RL-) - Body ground Always 10 kΩ or higher
      O6-4 (+) - Body ground Always 10 kΩ or higher
      O6-2 (-) - Body ground Always 10 kΩ or higher
      for RH Side (w/ Telematics Transceiver):
      Tester Connection Condition Specified Condition
      P32-5 (WFR+) - I40-2 (SPI+) Always Below 1 Ω
      P32-20 (WFR-) - I40-3 (SPI-) Always Below 1 Ω
      I40-5 (SPO+) - L9-1 Always Below 1 Ω
      I40-6 (SPO-) - L9-2 Always Below 1 Ω
      P32-13 (FR+) - J8-4 Always Below 1 Ω
      P32-28 (FR-) - J8-2 Always Below 1 Ω
      P32-9 (RR+) - N5-3 (+TW) Always Below 1 Ω
      P32-24 (RR-) - N5-1 (-TW) Always Below 1 Ω
      N5-4 (+) - N6-1 Always Below 1 Ω
      N5-2 (-) - N6-2 Always Below 1 Ω
      P32-5 (WFR+) - Body ground Always 10 kΩ or higher
      P32-20 (WFR-) - Body ground Always 10 kΩ or higher
      I40-5 (SPO+) - Body ground Always 10 kΩ or higher
      I40-6 (SPO-) - Body ground Always 10 kΩ or higher
      P32-13 (FR+) - Body ground Always 10 kΩ or higher
      P32-28 (FR-) - Body ground Always 10 kΩ or higher
      P32-9 (RR+) - Body ground Always 10 kΩ or higher
      P32-24 (RR-) - Body ground Always 10 kΩ or higher
      N5-4 (+) - Body ground Always 10 kΩ or higher
      N5-2 (-) - Body ground Always 10 kΩ or higher
      for RH Side (w/o Telematics Transceiver):
      Tester Connection Condition Specified Condition
      P32-5 (WFR+) - L9-1 Always Below 1 Ω
      P32-20 (WFR-) - L9-2 Always Below 1 Ω
      P32-13 (FR+) - J8-4 Always Below 1 Ω
      P32-28 (FR-) - J8-2 Always Below 1 Ω
      P32-9 (RR+) - N5-3 (+TW) Always Below 1 Ω
      P32-24 (RR-) - N5-1 (-TW) Always Below 1 Ω
      N5-4 (+) - N6-1 Always Below 1 Ω
      N5-2 (-) - N6-2 Always Below 1 Ω
      P32-5 (WFR+) - Body ground Always 10 kΩ or higher
      P32-20 (WFR-) - Body ground Always 10 kΩ or higher
      P32-13 (FR+) - Body ground Always 10 kΩ or higher
      P32-28 (FR-) - Body ground Always 10 kΩ or higher
      P32-9 (RR+) - Body ground Always 10 kΩ or higher
      P32-24 (RR-) - Body ground Always 10 kΩ or higher
      N5-4 (+) - Body ground Always 10 kΩ or higher
      N5-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO.1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  6. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  7. CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    B

    GO TO STEP 9 Click here

    A

  8. INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)


    1. B008IFZC35
      *a

      Component without harness connected

      (DCM [Telematics Transceiver])

      Remove the DCM (telematics transceiver).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (SPO+) - 2 (SPI+) Always Below 1 Ω
      6 (SPO-) - 3 (SPI-) Always Below 1 Ω
      5 (SPO+) - Body ground Always 10 kΩ or higher
      6 (SPO-) - Body ground Always 10 kΩ or higher
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

    OK

  9. CHECK REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for LH Side

      *2: for RH Side

      *3: w/ Telematics Transceiver


    1. Disconnect the I155 radio receiver assembly connector.

    2. Disconnect the M9*1 and/or L9*2 front No. 1 speaker assembly connector.

    3. Disconnect the J9*1 and/or J8*2 front No. 2 speaker assembly connector.

    4. Disconnect the O6*1 and/or N5*2 rear No. 2 speaker assembly connector.

    5. Disconnect the O5*1 and/or N6*2 rear speaker assembly connector.

    6. Disconnect the I40 DCM (telematics transceiver) connector.*3

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH Side:
      Tester Connection Condition Specified Condition
      I155-2 (FL+) - J9-3 (+TW) Always Below 1 Ω
      I155-7 (FL-) - J9-1 (-TW) Always Below 1 Ω
      J9-4 (+) - M9-1 Always Below 1 Ω
      J9-2 (-) - M9-2 Always Below 1 Ω
      I155-3 (RL+) - O6-3 (+TW) Always Below 1 Ω
      I155-8 (RL-) - O6-1 (-TW) Always Below 1 Ω
      O6-4 (+) - O5-1 Always Below 1 Ω
      O6-2 (-) - O5-2 Always Below 1 Ω
      I155-2 (FL+) - Body ground Always 10 kΩ or higher
      I155-7 (FL-) - Body ground Always 10 kΩ or higher
      J9-4 (+) - Body ground Always 10 kΩ or higher
      J9-2 (-) - Body ground Always 10 kΩ or higher
      I155-3 (RL+) - Body ground Always 10 kΩ or higher
      I155-8 (RL-) - Body ground Always 10 kΩ or higher
      O6-4 (+) - Body ground Always 10 kΩ or higher
      O6-2 (-) - Body ground Always 10 kΩ or higher
      for RH Side (w/ Telematics Transceiver):
      Tester Connection Condition Specified Condition
      I155-1 (FR+) - I40-2 (SPI+) Always Below 1 Ω
      I155-6 (FR-) - I40-3 (SPI-) Always Below 1 Ω
      I40-5 (SPO+) - J8-3 (+TW) Always Below 1 Ω
      I40-6 (SPO-) - J8-1 (-TW) Always Below 1 Ω
      J8-4 (+) - L9-1 Always Below 1 Ω
      J8-2 (-) - L9-2 Always Below 1 Ω
      I155-4 (RR+) - N5-3 (+TW) Always Below 1 Ω
      I155-9 (RR-) - N5-1 (-TW) Always Below 1 Ω
      N5-4 (+) - N6-1 Always Below 1 Ω
      N5-2 (-) - N6-2 Always Below 1 Ω
      I155-1 (FR+) - Body ground Always 10 kΩ or higher
      I155-6 (FR-) - Body ground Always 10 kΩ or higher
      I40-5 (SPO+) - Body ground Always 10 kΩ or higher
      I40-6 (SPO-) - Body ground Always 10 kΩ or higher
      J8-4 (+) - Body ground Always 10 kΩ or higher
      J8-2 (-) - Body ground Always 10 kΩ or higher
      I155-4 (RR+) - Body ground Always 10 kΩ or higher
      I155-9 (RR-) - Body ground Always 10 kΩ or higher
      N5-4 (+) - Body ground Always 10 kΩ or higher
      N5-2 (-) - Body ground Always 10 kΩ or higher
      for RH Side (w/o Telematics Transceiver):
      Tester Connection Condition Specified Condition
      I155-1 (FR+) - J8-3 (+TW) Always Below 1 Ω
      I155-6 (FR-) - J8-1 (-TW) Always Below 1 Ω
      J8-4 (+) - L9-1 Always Below 1 Ω
      J8-2 (-) - L9-2 Always Below 1 Ω
      I155-4 (RR+) - N5-3 (+TW) Always Below 1 Ω
      I155-9 (RR-) - N5-1 (-TW) Always Below 1 Ω
      N5-4 (+) - N6-1 Always Below 1 Ω
      N5-2 (-) - N6-2 Always Below 1 Ω
      I155-1 (FR+) - Body ground Always 10 kΩ or higher
      I155-6 (FR-) - Body ground Always 10 kΩ or higher
      J8-4 (+) - Body ground Always 10 kΩ or higher
      J8-2 (-) - Body ground Always 10 kΩ or higher
      I155-4 (RR+) - Body ground Always 10 kΩ or higher
      I155-9 (RR-) - Body ground Always 10 kΩ or higher
      N5-4 (+) - Body ground Always 10 kΩ or higher
      N5-2 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT FRONT NO.1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  12. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  13. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

    OK

  14. CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Result
      Result Proceed to
      w/ Telematics Transceiver A
      w/o Telematics Transceiver B

    B

    GO TO STEP 16 Click here

    A

  15. INSPECT DCM (TELEMATICS TRANSCEIVER) (SPO+, SPO-, SPI+, SPI-)


    1. B008IFZC35
      *a

      Component without harness connected

      (DCM [Telematics Transceiver])

      Remove the DCM (telematics transceiver).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      5 (SPO+) - 2 (SPI+) Always Below 1 Ω
      6 (SPO-) - 3 (SPI-) Always Below 1 Ω
      5 (SPO+) - Body ground Always 10 kΩ or higher
      6 (SPO-) - Body ground Always 10 kΩ or higher
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

    OK

  16. CHECK REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here