SHIFT AND SELECT TRANSMISSION CONTROL CABLE INSTALLATION


  1. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B007TQJ

      Pass the control cable assembly through the floor hole.

    2. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. B007U7J

      Wide body LHD steering position type:


      1. Install the No. 3 control cable bracket to the transmission control cable assembly.

      2. Install the No. 3 control cable bracket with the 2 nuts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    4. B007PAC

      Install the front floor footrest with the 2 nuts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    5. B007QZME01

      Install the transmission control cable assembly to the shift lever.

      Note

      Install the transmission control cable assembly so that the end section of the select cable indicated by the arrow, as shown in the side view, (A in the illustration) faces upward.

    6. B007Q4JE01

      Turn the control cable assembly adjust nut clockwise 180°. While holding the adjust nut, push in the locks.

    7. Install the control cable assembly to the shift lever.

      Tech Tips

      When the cable is installed to the shift lever, the locks are released and the adjust nut rotates 180°. Then, the locks are engaged again.

      Note

      Make sure that the control cable assembly is firmly installed to the shift lever.

  2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    1. B007VSZ

      Install the No. 2 control cable bracket to the transmission control cable assembly.

    2. Install the No. 2 control cable bracket with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    3. B007OCT

      Install the clamp with the bolt.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    4. B007VQT

      Install the control cable support to the control cable assembly.

    5. Install the control cable support with the bolt.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    6. B007T5UE01

      Install new 2 clips to the NO. 1 transmission control cable bracket.

    7. Install the transmission control cable assembly to the No. 1 transmission control cable bracket.

      Note


      • Be sure that A claws of the clips are firmly engaged into the bracket grooves.

      • Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.

    8. B007VCTE02

      Align the matchmarks on the control cable assembly and the shift outer lever.

    9. Align the matchmarks on the control cable assembly and the select outer lever.

    10. Install the transmission control cable assembly to the shift outer lever with the nut.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    11. Install the transmission control cable assembly to the select outer lever with the nut.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  3. INSTALL TRANSMISSION CONTROL CABLE INSULATOR (for RHD) (w/ DPF)


    1. B007OMA

      Install the No. 1 transmission control cable insulator to the select outer lever with the nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Install the No. 2 transmission control cable insulator to the No. 1 transmission control cable bracket with the 2 nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    1. Attach the 8 claws to install the instrument panel finish panel lower center.

  5. INSTALL SHIFTING HOLE COVER ASSEMBLY


    1. for Manual Transmission:

      Attach the 6 claws to install the shifting hole cover assembly.

    2. for Automatic Transmission:

      Attach the 8 claws to install the shifting hole cover assembly.

  6. INSTALL SHIFT LEVER KNOB


    1. B007UJDE01
      Text in Illustration
      *A for Manual Transmission
      *B for Automatic Transmission

      Turn the shift lever knob in the direction indicated by the arrow and install it.

  7. INSTALL PARKING BRAKE HOLE COVER


    1. Attach the 6 claws to install the parking brake hole cover.

  8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Attach the 3 claws to instrument panel under cover sub-assembly No. 1.

    2. Install the the 2 clips.

  9. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    1. Connect the fuel lid lock control cable and bonnet (hood) control cable assembly to the instrument panel finish lower.

    2. Attach the 4 clips to install the instrument panel finish panel lower.

    3. Install the 2 clips.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  11. PERFORM INITIALIZATION

    Some systems need initialization after reconnecting the cable to the negative battery terminal Click here.