FUEL TANK(w/ Canister Pump Module) REMOVAL

CAUTION / NOTICE / HINT

Note

When disconnecting the fuel tank to filler pipe hose, fuel remaining in the fuel tank assembly may be discharged.

PROCEDURE


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT FLOOR COVER CENTER LH

    B008HGR

    1. Remove the bolt, 2 nuts and 6 clips from the front floor cover center LH.

    2. B008IEL

      Loosen the nut and remove the front floor cover center LH.

  5. REMOVE NO. 2 FLOOR UNDER COVER


    1. B008GUQ

      Detach the clip and loosen the 2 nuts and No. 2 floor under cover.

  6. DISCONNECT FUEL TANK TO CANISTER TUBE SUB-ASSEMBLY


    1. B008IVS

      Disconnect the connector from the charcoal canister assembly.

    2. Detach the 3 clamps and disconnect the fuel gauge wire.

    3. B008IO7

      Disconnect the fuel tank to canister tube sub-assembly from the charcoal canister assembly.

      Click here

  7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B008HLZ

      Disconnect the 2 fuel tank main tube sub-assemblies from the 2 fuel pipes.

      Click here

  8. DRAIN FUEL

    Note


    • When disconnecting the fuel tank to filler pipe hose, fuel remaining in the fuel tank assembly may be discharged.

    • Be aware that fuel discharging cannot be performed if the fuel pump is malfunctioning.


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay


      Powertrain > Engine > Active Test
      Tester Display
      Activate the Circuit Relay

    6. According to the display on the GTS, operate the fuel pump and discharge the fuel from the fuel tank main tube sub-assembly.

      CAUTION:


      • Do not smoke or be near an open flame when working on the fuel system.

      • Secure good ventilation.

      • Keep gasoline away from rubber or leather parts.

    7. Disconnect the cable from the negative (-) battery terminal.

  9. REMOVE FUEL HOSE PROTECTOR


    1. B008IXJ

      Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.

  10. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

    Note

    Be careful when discharging the remaining fuel from the fuel tank assembly.


    1. B008ITZ

      Loosen the hose clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.

  11. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    1. B008IOF

      Detach the clamp and disconnect the fuel tank vent hose sub-assembly from the No. 2 fuel tank band sub-assembly.

  12. DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    1. B008JI7

      Disconnect the fuel tank breather tube sub-assembly from the fuel tank filler pipe sub-assembly.

      Click here

  13. REMOVE FUEL TANK ASSEMBLY


    1. B008J17

      Disconnect the 3 clamps from the 2 No. 4 fuel tube clamps and the bracket on the vehicle side.

    2. Using an engine lifter and attachments, support the fuel tank assembly.

    3. B008JOL

      Remove the 2 bolts and No. 1 fuel tank band sub-assembly.

    4. Remove the 4 bolts and 2 No. 2 fuel tank band sub-assemblies.

    5. Slightly lower the engine lifter.

      Note

      Be careful not to cut the fuel gauge wire.

    6. B008HHU

      Disconnect the 2 connectors from the fuel sender gauge assembly and fuel suction tube assembly with pump.

      Note


      • Before starting the operation, check that there is no mud or other dirt on the connector.

      • Do not use any tools.

    7. Detach the 3 clamps from the No. 3 fuel tube clamp, No. 4 fuel tube clamp and No. 5 fuel tube clamp, and disconnect the fuel gauge wire from the fuel tank assembly.

  14. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

    Click here

  15. REMOVE FUEL TANK VENT TUBE SET PLATE

    Click here

  16. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP

    Click here

  17. REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here

  18. REMOVE FUEL TANK TO CANISTER TUBE SUB-ASSEMBLY


    1. B008J13

      Remove the fuel tank to canister tube sub-assembly from the fuel tank assembly.

      Click here

  19. REMOVE FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    1. B008I2D

      Detach the clamp and remove the fuel tank breather tube sub-assembly from the fuel tank assembly.

      Click here

  20. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B008IJ4

      Disconnect the 5 clamps and remove the fuel tank main tube sub-assembly from the No. 3 fuel tube clamp, 3 No. 4 fuel tube clamps and No. 5 fuel tube clamp.

  21. REMOVE NO. 3 FUEL TUBE CLAMP


    1. Remove the No. 3 fuel tube clamp from the fuel tank assembly.

  22. REMOVE NO. 4 FUEL TUBE CLAMP


    1. Remove the 3 No. 4 fuel tube clamps from the fuel tank assembly.

  23. REMOVE NO. 5 FUEL TUBE CLAMP


    1. Remove the No. 5 fuel tube clamp from the fuel tank assembly.